User manual SANYO PLCXR70N

[. . . ] Multimedia Rear-Projection Display MODEL PLC-XR70N , , , , , , , , , , , , , , , , , , , , , , , , Owner's Manual INFORMATION TO THE USER NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause har mful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. TO THE OWNER As the owner of a new Rear-Projection Display, you are probably eager to try out your new projector. [. . . ] To cut off the audio sound, point the arrow to "Mute" and then press the SELECT (REAR CLICK) button. To restore the sound to its previous volume level, set the Mute to Off. Mute PICTURE FREEZE FUNCTION Press the FREEZE button on the Remote Control Unit, and the picture will remain on-screen. This function is cancelled when the FREEZE button is pressed again or any other function button is pressed. 25 COMPUTER MODE SELECTING COMPUTER MODE Direct Operation Press the MODE button on the Front Control or the PC button on Remote Control Units. Select the Mode among Computer1 to Computer 3 corresponding with the input source. The display of "Computer 1, " "Computer 2, " "Computer 3, " "Video 1, " "Video 2, " or "Video 3"appears on the screen for a few second. (The "Computer 1, " "Computer 2, " or "Computer 3" appears when pressing the PC button. ) Computer 1 Computer 2 Computer 3 Displaying the image from "Computer 1" on the Rear Terminal. Displaying the image from "Computer 2" on the Front Terminal. Displaying the image from "Computer 3" on the Front Terminal. MODE button Computer 1 Computer 2 Computer 3 Video 1 Video 2 Video 3 PC button Computer 1 Computer 2 Computer 3 Menu Operation 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select Computer and press the SELECT (REAR CLICK) button. Move the arrow to the mode among Computer1 to Computer3 that you want to select, and then press the SELECT (REAR CLICK) button. 36 5 60 0 + + Providing the information of the computer detected by the projector. CURRENT MODE DISPLAY When selecting the "Computer 1, " "Computer 2, " or "Computer 3" Mode, the Current Mode display appears. It shows the information of the computer of the mode selected. 26 COMPUTER MODE SELECTING COMPUTER SYSTEM Automatic Multiscanning system This projector automatically adapt to most different types of computer based on VGA, SVGA or XGA (refer to "COMPATIBLE COMPUTER SPECIFICATION" on page 28). When selecting "Computer 1, " "Computer 2, " or "Computer 3", this projector become automatically suited to the incoming signal and projectors the proper image without any special setting. (Setting of the Computer System may be required when connecting some computers. ) Note : The projector may provides the messages below. Go PC adj. The projector cannot discriminate or detect the input signal from the computer. (Refer to PC ADJUSTMENT on page 28. ) There is no signal from the computer on the any terminal (the Rear Terminal or the Front Terminal). Make sure the connection of the computer and the projector is set correctly. (Refer to TROUBLESHOOTING on page 43. ) VGA 1 SYSTEM BOX It displays the SYSTEM being selected. No signal Selecting Computer System Manually To set the Computer system manually, select the Mode from the COMPUTER SYSTEM Menu on the ON-SCREEN MENU. The system being selected. 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SELECT (REAR CLICK) button. (The COMPUTER MODE Menu also appears by pressing the SYSTEM button on the Front Control or the Remote Control Units. ) Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the system that you want to set, and then press SELECT (REAR CLICK) button. VGA 1 VGA 1 VGA 2 VGA 3 MODE 1 MODE 2 The system on this dialog box can be selected. 2 It terminates the SYSTEM Menu. When this mark is displayed as black, more computer system modes will be available. Move the arrow to this mark and then press the SELECT (REAR CLICK) button, and another mode will be displayed. 27 COMPUTER MODE PC ADJUSTMENT This Projector can automatically detect display signals from most personal computers currently distributed. [. . . ] (Refer to the page 42. ) No image. l Check the connection between the computer or video equipment and the projector. l When turning the projector on, it is about 30 seconds to display the image. l Check the system that you select is corresponding with the computer or the video equipment. l Make sure the temperature is not out of the Operating Temperature (5° ~ 35°). [. . . ]