User manual SANYO PLCXP10NA

[. . . ] If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Do not stare directly into the lens as it could possibly damage your eyes. Be especially careful that children do not stare directly into the beam. G Provide appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. [. . . ] (Signal formats provided in this projector is shown on page 43. ) Note : The projector displays one of the Auto, ---, Mode 1/2/3/4/5, or the system provided in the projector. Auto When the projector cannot recognize a connected signal as a PC system provided in this projector, the Auto PC Adjustment function operates to adjust the projector and the message "Auto" is displayed on the SYSTEM Menu icon. (Refer to P23. ) When the image is not provided properly, manual adjustment is required. (Refer to P24 and 25. ) There is no signal input from the connected computer. Make sure the connection of the computer and the projector is set correctly. (Refer to TROUBLESHOOTING on page 40. ) PC SYSTEM MENU SYSTEM Menu icon Displays system being selected. ­­­ SELECT COMPUTER SYSTEM MANUALLY PC system can also be selected manually. PC SYSTEM MENU 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to move the red frame pointer to the PC SYSTEM Menu icon. Press the POINT DOWN button to move the red arrow pointer to the system that you want to set, and then press the SELECT button. SYSTEM Menu icon Displays system being selected. (P24, 25) 22 COMPUTER INPUT PC ADJUSTMENT AUTO PC ADJUSTMENT Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your computer. Auto PC Adj. 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT button to move the red frame pointer to the PC ADJUST Menu icon. Press the POINT DOWN button to move the red frame pointer to the AUTO PC Adj. Press the POINT LEFT/RIGHT button(s) to decrease/increase value and then press the SELECT button. Full screen Press the POINT LEFT/RIGHT button(s) to switch the Full screen function to "On" or "Off. " Set "On" to resize the image with 4 x 3 aspect ratio to fit the screen. NOTE : Fine sync, Total dots, Display area (H/V), and Full screen cannot be adjusted when "1035i (HDTV)" or "1080i (HDTV)" is selected in the PC SYSTEM Menu (P22). Press the SELECT button at the Display area icon and the Display area dialog box appears. Display area Press the POINT LEFT /RIGHT button(s) to adjust value and then press the SELECT button. To store adjustment data. This Mode has parameters being stored. 3 Store To store adjustment parameters, move the red frame pointer to the Store icon and then press the SELECT button. Move the red arrow pointer to any of Mode 1 to 5 that you want to store to and then press the SELECT button. Mode free To clear adjustment parameters previously set, move the red frame pointer to Mode free icon and then press the SELECT button. Move the red arrow pointer to the Mode that you want to clear and then press the SELECT button. To clear adjustment data. Vacant Mode Shows values of "Total dots, " "Horizontal, " "Vertical, " "Display area H, " and "Display area V. " Store icon Close this dialog box. Mode free icon 25 COMPUTER INPUT PICTURE IMAGE ADJUSTMENTS IMAGE LEVEL SELECT (DIRECT) Select an image level among Standard, Real, Image 1, Image 2, Image 3 and Image 4 by pressing the IMAGE button on the Top Control or on the Remote Control. IMAGE 1~4 User preset picture adjustment in the IMAGE ADJUST Menu (P27). IMAGE button Standard Real Image 1 Image 2 Image 3 Image 4 IMAGE LEVEL SELECT (MENU) 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT button to move the red frame pointer to the IMAGE SELECT Menu icon. [. . . ] Make sure you are not too far from the projector when using the Remote Control. G Make sure the code of the Remote Control is set to conform to the projector. (See "SETTING" section on page 34, 35. ) G Check cable connection between the projector and your computer. G Turn the projector on before turning on the computer. Wireless Mouse function does not work. WARNING : High voltages are used to operate this projector. [. . . ]