User manual SANYO PLCXE40

[. . . ] Multimedia Projector MODEL PLC-XE40 Owner's Manual Features and Design This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16. 77 million colors, and matrix liquid crystal display (LCD) technology. Large Screen in Limited Space - Short focus lens allows you to project large images from short distance. 14) Quick Termination The AC power cord can be unplugged immediately after turning off the projector without waiting for the projector to cool down. 20) Antitheft Alarm Function This projector is equipped with an Antitheft alarm function which sounds when a vibration is detected. [. . . ] Press the SELECT button at "Common" to display the confirmation box. Press the SELECT button at "Reset" to display the confirmation box. To reset, press the SELECT button at "Yes". Press the SELECT button at "Common" or "Reset", to display confirmation box. Note: ·When no signal is detected, Normal is set automatically and "Aspect" screen disappears. · The adjustable range of Scale H/V and Position H/V can be limited depending on the input signal. For zooming in and out the images Digital zoom + When the Digital zoom + is selected, the On-Screen Menu disappears and "D. The Panning function can work only when the image is larger than the screen size. A projected image can be also expanded by pressing the D. ZOOM button on the remote control. Digital zoom ­ When Digital zoom ­ is selected, the On-Screen Menu disappears and "D. A projected image can be also compressed by pressing the D. ZOOM button on the remote control. To exit the Digital zoom +/­ mode, press any button except the D. ZOOM buttons, SELECT, and Point button. To return to the previous screen size, select a screen size in the Screen Size Adjustment or select an input source from the Input Source Selection (p. Remote Control POINT buttons SELECT button D. ZOOM + button D. ZOOM - button Note: · The panning function may not operate properly if the stored Mode in the PC Adjust Menu is used. 30) · The minimum compression ratio can be limited depending on the input signal or when the Keystone function is working. · True, Full screen, and Digital zoom +/­ cannot be selected when 480i, 575i, 480p, or 575p is selected in the PC System Menu (p. 27) · Digital zoom +/- cannot be selected when Full screen or True is selected. 34 Video Input Input Source Selection (Video, S-Video) Direct Operation Select Video by pressing the VIDEO button on the remote control. Before using VIDEO button, select the correct input source through menu operation as described below. Remote Control VIDEO button Menu Operation Input Menu icon Input Menu Move the pointer to Video and press the SELECT button. 1 2 3 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Input Menu icon. Press the Point ed buttons to move the red arrow pointer to Video and then press the SELECT button to display the Source Select Menu . VIDEO Source Select Menu (VIDEO) Move the pointer to the source that you want to select and then press the SELECT button. When selecting Auto, the projector automatically detects incoming video signal, and adjusts itself to optimize its performance. Video Video When video input signal is connected to the VIDEO jack, select Video. When video input signal is connected to the SVIDEO jack, select S-Video. Move the pointer to the source that you want to select and press the SELECT button. Auto Computer Input S-Video 35 Video Input Input Source Selection (Component, RGB Scart 21-pin) Direct Operation Select Computer 1 by pressing the COMPUTER button on the remote control. Before using COMPUTER button, select the correct input source through Menu operation as described below. Remote Control COMPUTER button COMPUTER button Computer 1 Computer 2 Menu Operation 1 2 3 Press the MENU button to display the On-Screen Menu. [. . . ] Quit 0 - 63 0 - 63 High Mid Low XLow Adj. Red Green Blue Sharpness Gamma Reset Store 0 - 63 0 - 63 0 - 63 0 - 15 0 - 15 Yes / No Image 1 Image 2 Image 3 Image 4 Quit Yes / No Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Quit Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Quit Store Quit Screen Quit Image Select Dynamic Standard Real Blackboard(Green) Image 1 Image 2 Image 3 Image 4 Normal True Wide Full screen Custom Scale H / V H&V On / Off Position H / V Common Yes / No Yes / No Reset Quit Digital zoom + Digital zoom ­ 60 Appendix Video Input System (2) Auto 1080i 1035i 720p 575p 480p 575i 480i Auto PAL SECAM NTSC NTSC 4. 43 PAL-M PAL-N Dynamic Standard Cinema Blackboard(Green) Image 1 Image 2 Image 3 Image 4 Setting Setting Language English German French Italian Spanish Portuguese Dutch Swedish Finnish Polish Hungarian Romanian Russian Chinese Korean Japanese Quit Store / Reset On / Off On / Countdown off / Off Logo select Off Default User Capture Yes / No Logo PIN code lock Logo PIN code entry Off On PIN code change Quit Quit Ceiling Rear Terminal Power management On / Off On / Off Computer 2 /Monitor out Off Ready Shut down Timer(1-30 Min) Quit On start Lamp control Remote control Security On / Off Normal / Auto / Eco Code 1 / Code 2 PIN code lock PIN code lock entry On / Off PIN code change Quit Alarm Off Small / Medium / Large Alarm volume Low / Medium / Large Sensitivity 10seconds / 60seconds Ringing time / Long time Quit On Quit L1 / L2 Hour(s) Reset Quit Yes / No System (3) Image Select Keystone Blue back Display Logo Image Adjust Contrast Brightness Color Tint Color temp. 0 - 63 0 - 63 0 - 63 0 - 63 High Mid Low XLow Adj. 0 - 63 0 - 63 0 - 63 0 - 15 0 - 15 Off L1 L2 Off L1 L2 Film Yes / No Image 1 Image 2 Image 3 Image 4 Quit Red Green Blue Sharpness Gamma Noise reduction Appendix Progressive Reset Store Quit Screen Normal Wide Custom Scale H / V H&V Position H / V Common Reset Quit On / Off Yes / No Yes / No Fan Lamp counter Factory default Quit 61 Appendix Indicators and Projector Condition Check the indicators for projector condition. Indicators POWER red/green WARNING red LAMP REPLACE yellow Projector Condition The projector is off. (The AC power cord is unplugged. ) The projector is preparing for stand-by or the projection lamp is being cooled down. The projector is ready to be turned on with the POWER ON-OFF button. The projector is operating normally. The projector is in the Power management mode. [. . . ]