User manual SANYO PLCSW10

[. . . ] Multimedia Projector MODEL PLC-SW10 Owner's Manual TO THE OWNER Before operating this projector, read this manual thoroughly and operate the projector properly. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Trouble-shooting" section of the end of this booklet. [. . . ] CURRENT MODE DISPLAY When selecting the Computer Mode, the Current Mode display appears. It shows the information of the computer of the mode selected. Providing the information of the computer detected by the projector. SELECTING COMPUTER SYSTEM AUTOMATIC MULTI-SCAN SYSTEM This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to "COMPATIBLE COMPUTER SPECIFICATION" on page 23). When selecting Computer, this projector automatically tunes to the incoming signal and projects the proper image without any special settings. (Setting of the Computer System may be required when connecting some computers. ) Note : The projector may display one of the following messages. SYSTEM BOX Displays the SYSTEM being selected. Go to PC adj. The projector cannot discriminate or detect the input signal from the computer. (Refer to page 24. ) No signal There is no signal input from the computer. Make sure the connection of the computer and the projector is set correctly. (Refer to TROUBLESHOOTING on page 37. ) The system being selected. SELECT COMPUTER SYSTEM MANUALLY To set the Computer system manually, select the mode on the ON-SCREEN MENU. 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SELECT button. Move the arrow to the system that you want to set, and then press SELECT button. The systems on these dialog boxes can be selected. Closes the SYSTEM Menu. 22 COMPUTER MODE COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 100 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION 640 x 480 720 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 ­­­­­ ­­­­­ VGA 1 VGA 2 VGA 3 VGA 4 VGA 5 VGA 6 VGA 7 MAC LC13 MAC 13 RGB RGB SVGA 1 SVGA 2 SVGA 3 SVGA 4 SVGA 5 SVGA 6 SVGA 7 SVGA 8 SVGA 9 SVGA 10 SVGA 11 MAC1 6 XGA 1 XGA 2 H-Freq. (kHz) 31. 47 31. 47 31. 47 37. 86 37. 86 37. 50 43. 269 34. 97 35. 00 15. 734 15. 625 35. 156 37. 88 46. 875 53. 674 48. 08 37. 90 34. 50 38. 00 38. 60 32. 70 38. 00 49. 72 48. 36 68. 677 V-Freq. (Hz) 59. 88 70. 09 70. 09 74. 38 72. 81 75. 00 85. 00 66. 60 66. 67 30 25 56. 25 60. 32 75. 00 85. 06 72. 19 61. 03 55. 38 60. 51 60. 31 51. 09 60. 51 74. 55 60. 00 84. 997 ON-SCREEN DISPLAY RESOLUTION 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 (Interlace) XGA 3 XGA 4 XGA 5 XGA 6 XGA 7 XGA 8 XGA 9 XGA 10 XGA 11 XGA 12 XGA 13 XGA 14 XGA15 MAC 19 MAC 21 SXGA 1 SXGA 11 SXGA 13 SXGA 14 SXGA 17 SXGA 18 HDTV720p HDTV1035i HDTV1080i H-Freq. (kHz) 60. 023 56. 476 60. 31 48. 50 44. 00 63. 48 36. 00 62. 04 61. 00 35. 522 46. 90 47. 00 58. 03 60. 24 68. 68 64. 20 61. 20 50. 00 50. 00 61. 85 46. 43 45. 00 33. 75 33. 75 V-Freq. (Hz) 75. 03 70. 07 74. 92 60. 02 54. 58 79. 35 43. 59 77. 07 75. 70 43. 48 58. 20 58. 30 72. 00 75. 08 75. 06 70. 40 65. 20 43. 00 47. 00 66. 00 43. 35 60. 00 60. 00 60. 00 1024 x 768 1024 x 768 1024 x 768 (Interlace) 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 870 1152 x 864 1152 x 900 1280 x 1024 (Interlace) 1280 x 1024 (Interlace) 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1152 x 900 1280 x 1024 (Interlace) ­­­­­ ­­­­­ ­­­­­ NOTE : Specifications are subject to change without notice. 23 COMPUTER MODE PC ADJUSTMENT This Projector can automatically tune to the display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from the standard ones and may not be tuned by the Multi-Scan system of this projector. If this happens, the projector cannot reproduce a proper image and the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has a PC ADJUSTMENT function, to enable you to precisely adjust several parameters to match with those special signal formats. This projector has five independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it. Note : This PC ADJUSTMENT function cannot be operated when "RGB, " "HDTV1035i" or "HDTV1080i" is selected on the SYSTEM MENU (P22 and 23). 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT RIGHT/LEFT buttons to select PC ADJUST and press the SELECT button. In this dialog box, you can store the parameter into the area from "Mode 1" to "Mode 5. " When memorizing the new computer parameter, select the Mode with the message "Free" by pressing the POINT UP/DOWN buttons and the SELECT button. [. . . ] q Wait 90 seconds after the projector is turned OFF before turning the projector back on. NOTE : After pressing the power ON-OFF switch to OFF, make sure the projector works as follows: 1. After 90 seconds, the READY indicator will light green again and the projector may be turned on by pressing the power ON-OFF button. (See "TURNING ON/OFF THE PROJECTOR" section on page 19. ) q Check the Projection Lamp. [. . . ]