User manual SANYO PLCSU60

[. . . ] Before you do, we suggest that your spend a little time reading this manual to familiarize yourself with the operating procedures, so that you will receive maximum satisfaction from the many features included in your new projector. This owner's manual will acquaint you with your projector's features. Through the years, we have found that many service requests were not caused by problems with our projectors. They were caused by problems that could have been prevented, if the owner had followed the instructions in the manual. [. . . ] Press ZOOM or v button to have the image larger, and press ZOOM or w button to have the smaller. Zoom The message disappears after 4 seconds. FOCUS Adjustment 1 2 Press FOCUS / button on the Top Control or FOCUS v/w on the Remote Control Unit to turn into the FOCUS mode. / or Focus The message disappears after 4 seconds. NO SHOW FUNCTION Press the NO SHOW button on the Remote Control Unit to turn the picture into black image. These function is cancelled when the NO SHOW button is pressed again or any other function button is pressed. No Show The message disappears after 4 seconds. 22 BASIC OPERATION SOUND ADJUSTMENT Direct Operation Sound Volume Adjustment Press the VOLUME (+/­) buttons (located on the Top Control or on the Remote Control Unit) to adjust the volume. Sound Mute Setting Press the MUTE button on the Remote Control Unit to cut off the sound. To restore the sound to its previous level, press the MUTE button again or press VOLUME (+/­) buttons. Press the MUTE button to set the Mute function On or Off. It indicates the roughly level of the volume. Menu Operation 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SOUND and press the SELECT button. Move the arrow to the item that you want to select by pressing the POINT UP/DOWN buttons. Move the arrow to v or w of "Volume" by pressing the POINT UP/ DOWN buttons. This enables you to recall the setting for a specific computer whenever you need it. 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select PC ADJUST and press the SELECT button. In this dialog box, you can store the parameter into the area from "Mode 1" to "Mode 8. " When memorizing the new computer parameter, select the Mode with the message of "Free" by pressing the POINT UP/DOWN buttons and SELECT button. To change the parameters of the Mode previously set, select the Mode with "Stored. " When the Mode is selected, Parameter adjustment dialog box appears. Adjust the each item to match with your computer. The number of the total vertical lines. Adjusting the horizontal width of the picture image. When the Mode is selected, below dialog box appears. Manual set Computer Mode (1 to 8). 3 Total lines Total dots Horizontal Vertical Clamp Height Width It closes the PC ADJUSTMENT Menu. Move the arrow to v or w and press SELECT button. 4 When the parameter data adjustment finishes to be set, select "Stored" and press the SELECT button. "OK?" dialog box is displayed for confirmation. Press SELECT button at this item to adjust "Clamp, " "Height, " or "Width. " Each of the keys operates as follow. Reset Mode free Stored Quit It recall the parameter data that previously adjusted. It closes the PC ADJUST Menu. 5 To select the Mode manually adjusted in PC ADJUSTMENT Menu, select the mode at the SYSTEM SELECT Menu. (Refer to page 24. ) 25 COMPUTER MODE COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 130 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION 640 x 480 720 x 400 640 x 400 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 VGA 1 VGA 2 VGA 3 VGA 4 VGA 5 VGA 6 SVGA 1 SVGA 2 SVGA 3 SVGA 4 SVGA 5 SVGA 6 SVGA 7 SVGA 8 SVGA 9 SVGA 10 SVGA 11 SVGA 12 H-Freq. (kHz) 31. 47 31. 47 31. 47 37. 86 37. 86 37. 50 35. 156 37. 88 46. 875 53. 674 48. 08 37. 90 34. 50 38. 00 38. 60 47. 90 32. 70 38. 00 V-Freq. [. . . ] In such an event, leave the projector OFF and wait until condensation disappears. (See "SETTING" section on page 32. ) q Check Ceiling feature. (See "SETTING" section on page 32. ) q Check Display feature. (See "SETTING" section on page 32. ) Picture is L/R reversed. No image. q Check the connection between the computer or video equipment and the projector. [. . . ]