User manual SANYO PLCSU20N

[. . . ] Multimedia Projector MODEL PLC-SU20N Owner's Manual INFORMATION TO THE USER NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. TO THE OWNER As the owner of a new Multimedia Projector, you are probably eager to try out your new projector. [. . . ] When selecting Computer, this projector automatically tunes to the incoming signal and projectors the proper image without any special setting. (Setting of the Computer System may be required when connecting some computers. ) Note : The projector may provides the messages below. SYSTEM BOX Display the SYSTEM being selected. Go to PC adj. The projector cannot discriminate or detect the input signal from the computer. (Refer to page 24. ) No signal There is no signal input from the computer. Make sure the connection of the computer and the projector is set correctly. (Refer to TROUBLESHOOTING on page 35. ) SELECT COMPUTER MODE MANUALLY To set the Computer system manually, select the mode on the ONSCREEN MENU. The system being selected. 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SELECT button. Move the arrow to the system that you want to set, and then press SELECT button. The systems on this dialog box can be selected. Close the SYSTEM Menu. 22 COMPUTER MODE COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with the V, H-Frequency mentioned below and less than 135 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION 640 x 480 720 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 (Interlace) 768 x 576 (Interlace) VGA 1 VGA 2 VGA 3 VGA 4 VGA 5 VGA 6 MAC LC13 MAC 13 RGB RGB SVGA 1 SVGA 2 SVGA 3 SVGA 4 SVGA 5 SVGA 6 SVGA 7 SVGA 8 SVGA 9 H-Freq. (kHz) 31. 47 31. 47 31. 47 37. 86 37. 86 37. 50 34. 97 35. 00 15. 734 15. 625 35. 156 37. 88 46. 875 53. 674 48. 08 37. 90 34. 50 38. 00 38. 60 V-Freq. (Hz) 59. 88 70. 09 70. 09 74. 38 72. 81 75. 00 66. 60 66. 67 30 25 56. 25 60. 32 75. 00 85. 06 72. 19 61. 03 55. 38 60. 51 60. 31 ON-SCREEN DISPLAY RESOLUTION 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 (Interlace) SVGA 10 SVGA 11 SVGA 12 MAC1 6 XGA 1 XGA 2 XGA 3 XGA 4 XGA 5 XGA 6 XGA 7 XGA 8 XGA 9 XGA 10 XGA 11 XGA 12 XGA 13 XGA 14 MAC 19 H-Freq. (kHz) 47. 90 32. 70 38. 00 49. 72 48. 36 68. 677 60. 023 56. 476 60. 31 48. 50 44. 00 63. 48 36. 00 62. 04 61. 00 35. 522 46. 90 47. 00 60. 24 V-Freq. (Hz) 71. 92 51. 09 60. 51 74. 55 60. 00 84. 997 75. 03 70. 07 74. 92 60. 02 54. 58 79. 35 43. 59 77. 07 75. 70 43. 48 58. 20 58. 30 75. 08 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 (Interlace) 1024 x 768 1024 x 768 1024 x 768 NOTE : Specifications are subject to change without notice. 23 COMPUTER MODE PC ADJUSTMENT This Projector can automatically tune to the display signals from most personal computers currently distributed. However, some computers employ the special signal formats which are different from the standard ones and may not be tuned by Multiscanning of this projector. If this happens, the projector cannot reproduce a proper image and the image is recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has PC ADJUSTMENT function, to enable you to precisely adjust several parameters to match with those exceptional signal formats and the projector has five independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it. 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT RIGHT/LEFT buttons to select PC ADJUST and press the SELECT button. In this dialog box, you can store the parameter into the area from "Mode 1" to "Mode 5. " When memorizing the new computer parameter, select the Mode with the message "Free" by pressing the POINT UP/DOWN buttons and the SELECT button. To change the parameters of the Mode previously set, select the Mode with "Stored. " When the Mode is selected, Parameter adjustment dialog box appears. Move the arrow to the item that you want to change by pressing the POINT UP/DOWN buttons, and adjust each item to match with your computer. To change the value, press either the POINT RIGHT button or the POINT LEFT button. To activate the Mode manually adjusted in this PC ADJUSTMENT Menu, select the Mode at the SYSTEM SELECT Menu. [. . . ] q Make sure nothing is between the Remote Receiver and the Remote Control Units. q Make sure you are not too far from the projector when using the Remote Control Units. q Turn the projector on before you turn on the computer. Wireless Mouse function does not work. WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. Sanyo Service is easily obtained. [. . . ]