User manual SANYO PLCEF12EL

[. . . ] Multimedia Projector MODEL PLC-EF12N/12NL PLC-EF12E/12EL PLC-EF12B/12BL Owner's Manual TO THE OWNER Before operating this projector, read this manual thoroughly and operate the projector properly. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Trouble-shooting" section of the end of this booklet. [. . . ] (Refer to P47) 31 BASIC OPERATION TURNING ON/OFF THE PROJECTOR TO TURN ON THE PROJECTOR Connect the projector to a source (Computer, VCR, Video Camera, Video Disc Player, etc. ) using the appropriate terminals on the side of the projector (See "CONNECTING THE PROJECTOR" section on pages 13-22). Connect the projector's AC power cord into a wall outlet and turn the MAIN ON/OFF switch (located on the side of the projector) to the ON position. The LAMP POWER indicator will light RED, the READY indicator will light GREEN. Press the POWER ON/OFF button on the remote control unit or on the projector to ON. The LAMP POWER indicator light will dim and the cooling fans will operate. The wait display appears on the screen and the count-down starts (30-29-28-. . . 1). The signal from the source appears after 30 seconds. 30 TO TURN OFF THE PROJECTOR Press the POWER ON/OFF button on the remote control unit or on the projector. The LAMP POWER indicator will light bright and READY indicator will turn off. The cooling fans will operate for 90 seconds after the projector is turned off. (During this "cooling down" period, the projector cannot be turned on. ) The READY indicator will light green again and the projector may be turned on by pressing the POWER ON/OFF button. To power down completely, turn the MAIN ON/OFF switch (located on the side of the projector) to the OFF position. TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU TURN THE PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF. When the Power Management function is ON, the Projector detects the signal interruption and turns the Projection Lamp off automatically. When the TEMPERATURE WARNING indicator flashes red, the projector is automatically turned off. When the TEMPERATURE WARNING indicator continues to flash, follow procedures below: 1. Turn the MAIN ON / OFF SWITCH to OFF and disconnect the AC power cord from the AC outlet. If the TEMPERATURE WARNING indicator should still continue to flash, contact the sales dealer where you purchased this projector or service center. NOTE: The Cooling Fan may work for cooling while the projector is turned off. When the Cooling Fan is working, TEMPERATURE WARNING INDICATOR flashes red. 32 BASIC OPERATION ADJUSTING THE IMAGE ZOOM ADJUSTMENT Use Top control and Wireless/Wired remote control unit. Press the ZOOM (v) or (w) button to obtain your desired picture size. For a larger picture, press (v) and for a smaller picture, press (w). Use Wireless remote control unit. Press the ZOOM button and press POINT UP/DOWN button(s) to obtain your desired picture size. For a larger picture, press (UP) and for a smaller picture, press (DOWN). FOCUS ADJUSTMENT Use Top control and Wireless/Wired remote control unit. Press the FOCUS (v) or (w) button for a sharper, crisper picture. Use Wireless remote control unit. Press the FOCUS button and press POINT UP/DOWN button(s) to obtain a sharper, crisper picture. The Focus display will be displayed on the screen for a few seconds. LENS SHIFT FUNCTION Use Top control and Wireless/Wired remote control unit. Press the LENS SHIFT (v) or (w) button to obtain your desired screen position. Use Wireless remote control unit. Press the LENS SHIFT button and press POINT UP/DOWN button(s) to obtain your desired screen position. The Lens shift display will be displayed on the screen for a few seconds. DIGITAL ZOOM FUNCTION Press the D. The "D. zoom" and the magnifying-glass icon is displayed to indicate Digital zoom mode. [. . . ] If the image still does not display, unplug the projector from the computer and check the computer monitor's display. The problem may be with your graphics controller rather than with the projector. (When you reconnect the projector, remember to turn the computer and monitor off before you power up the projector. If the problem still exists, check the following chart. Problem: No power. q q q q q Try these Solutions: Plug the projector into an AC outlet. [. . . ]