User manual SANYO PLCEF10NA

[. . . ] Multimedia Projector MODEL PLC-EF10NA MOD PLC-EF10NAL (Without Lens) Owner's Manual INFORMATION TO THE USER NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the owner's manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. TO THE OWNER As the owner of a new Multi-media Projector, you are probably eager to try out your new projector. [. . . ] In case this happens, this projector allows you to choose a specific broadcast signal format. Connect the video equipment to the PROJECTOR and turn the projector on first. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. Press the POINT LEFT/RIGHT BUTTON(s) to select SYSTEM and press the SELECT (REAR CLICK) BUTTON. To change the current COLOR SYSTEM, press the POINT UP/DOWN BUTTON(s) to move the arrow to a desirable system and then press the SELECT (REAR CLICK) BUTTON. The setting changed remains effective until the MAIN ON/OFF switch is turned off. 4. COLOR SYSTEM DISPLAY VIDEO SOURCE SELECT Connect the video equipment to the PROJECTOR and turn the projector on first. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. Press the POINT LEFT/RIGHT BUTTON(s) to select VIDEO SOURCE and press the SELECT (REAR CLICK) BUTTON. To change the current VIDEO SOURCE, press the POINT UP/DOWN BUTTON(s) to move the arrow to a desirable video source and then press the SELECT (REAR CLICK) BUTTON. The setting changed remains effective until the MAIN ON/OFF switch is turned off. 4. VIDEO SOURCE DISPLAY 37 VIDEO MODE PICTURE IMAGE ADJUSTMENT Picture adjustments have been preset at the factory. Press the POINT LEFT/RIGHT BUTTON(s) to select IMAGE and press the SELECT (REAR CLICK) BUTTON. In this dialog box, you can adjust the settings by increasing or decreasing the levels shown as numbers. The items and the range of the levels that you can adjust are summarized in the table below. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s). To increase the level, point the arrow to v and then press the SELECT (REAR CLICK) BUTTON. To decrease the level, point the arrow to w and then press the SELECT (REAR CLICK) BUTTON. You may want to store the settings in the memory so that you can recall them later. To store the settings, move the arrow to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, "OK ?" is displayed for confirmation. The stored settings are memorized even if the MAIN ON/OFF is switched off. [. . . ] Do not attempt to open the cabinet. You can often correct operating problems yourself. If the projector fails to work properly, see "TROUBLESHOOTING" section on pages 55-56. If after following all operating instructions, you find that service is necessary, contact the SFS Corporation in Los Angeles, or the store where you purchased the unit. We will advise you how to obtain service. 56 APPENDIX TECHNICAL SPECIFICATIONS Projector Type Dimensions (W x H x D) Net Weight LCD Panel System Number of Pixels Color System Scanning Frequency Projection Image Size (Diagonal) Horizontal Resolution Projection Lens Motorized Lens Shift Throw Distance Projection Lamp AV Input Jacks Video Monitor Output Jack Audio Monitor Output Jacks Computer Input 1 Jack Computer Input 2 Jack Computer Audio Input Jack Computer Output Jack Computer Audio Output Jack Other Jack Built-in Speaker Image Elevation Adjustment Voltage Power Consumption Operating Temperature Storage Temperature Remote Control Transmitters Multi-media Projector 15. 4" (390 mm) x 9. 6" (245 mm) x 23" (585 mm) 39. 2 Ibs (17. 8 kg) 1. 8" TFT Active Matrix type x 3 panels 3, 932, 160 {1, 310, 720 (1, 280 x 1, 024) x 3} 6 color system (PAL, SECAM, NTSC, NTSC4. 43, PAL-M and PAL-N) H-sync. [. . . ]