User manual SANYO PLC9000NL

[. . . ] If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Be especially careful that children do not stare directly into the beam. G Take appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. [. . . ] When selecting Computer, this projector automatically tunes to incoming signal and projects proper image without any special setting. (Some computers need setting manually. ) Note : Projector may display one of the following messages. Auto When projector cannot recognize connected signal as PC system provided in this projector, Auto PC Adjustment function operates to adjust projector and the message "Auto" is displayed on SYSTEM Menu icon. (Refer to P24. ) When image is not provided properly, manual adjustment is required. Make sure the connection of computer and a projector is set correctly. (Refer to TROUBLESHOOTING on page 41. ) PC SYSTEM MENU SYSTEM Menu icon Displays system being selected. ­­­­ SELECT COMPUTER SYSTEM MANUALLY This projector automatically selects PC system among those provided in this projector and PC system can be also selected manually. PC SYSTEM MENU 1 2 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to PC SYSTEM Menu icon. Press POINT DOWN button to move a red arrow pointer to the system that you want to set, and then press SELECT button. SYSTEM Menu icon Displays system being selected. (P25, 26) 22 COMPUTER INPUT COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION 640 x 480 720 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 ­­­­­­­­ ­­­­­­­­ VGA 1 VGA 2 VGA 3 VGA 4 VGA 5 VGA 6 VGA 7 MAC LC13 MAC 13 RGB RGB SVGA 1 SVGA 2 SVGA 3 SVGA 4 SVGA 5 SVGA 6 SVGA 7 SVGA 8 SVGA 9 SVGA 10 SVGA 11 MAC 16 XGA 1 XGA 2 XGA 3 XGA 4 XGA 5 XGA 6 XGA 7 XGA 8 XGA 9 XGA 10 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 H-Freq. (kHz) 31. 47 31. 47 31. 47 37. 86 37. 86 37. 50 43. 269 34. 97 35. 00 15. 625 15. 734 35. 156 37. 88 46. 875 53. 674 48. 08 37. 90 34. 50 38. 00 38. 60 32. 70 38. 00 49. 72 48. 36 68. 677 60. 023 56. 476 60. 31 48. 50 44. 00 63. 48 36. 00 62. 04 V-Freq. (Hz) 59. 88 70. 09 70. 09 74. 38 72. 81 75. 00 85. 00 66. 60 66. 67 50 (Interlace) 60 (Interlace) ON-SCREEN DISPLAY RESOLUTION 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 870 1152 x 864 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 960 1152 x 900 1152 x 900 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1152 x 900 1280 x 1024 1280 x 1024 1280 x 960 1280 x 1024 ­­­­­­­­ ­­­­­­­­ ­­­­­­­­ ­­­­­­­­ 56. 25 60. 32 75. 00 85. 06 72. 19 61. 03 55. 38 60. 51 60. 31 51. 09 60. 51 74. 55 60. 00 84. 997 75. 03 70. 07 74. 92 60. 02 54. 58 79. 35 87. 17 (Interlace) XGA 11 XGA 12 XGA 13 XGA 14 XGA 15 MAC 19 MAC 21 SXGA 1 SXGA 2 SXGA 3 SXGA 4 SXGA 5 SXGA 6 SXGA 7 SXGA 8 SXGA 9 SXGA 10 SXGA 11 SXGA 12 SXGA 13 SXGA 14 SXGA 15 SXGA 16 SXGA 17 SXGA 18 SXGA 19 MAC MAC 720p (HDTV) 1035i (HDTV) 1080i 60(HDTV) 1080i 50(HDTV) H-Freq. Press POINT LEFT/RIGHT button(s) and adjust number to match your PC image. Current mode Press SELECT button to show the information of computer selected. Press SELECT button at this icon to adjust "Clamp, " "Display area (H/V)" or set "Full screen. " Selected Mode Shows status (Stored / Free) of the selected Mode. Press SELECT button at Current mode icon to show the information of computer connected. 25 COMPUTER INPUT Display area Selects area displayed with this projector. Display area H Adjustment of horizontal area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button. Display area V Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button. Full screen Press POINT LEFT/RIGHT button(s) to switch Full screen function to "On" or "Off. " Set "On" to resize the image with 4 x 3 aspect ratio to fit the screen. NOTE : Fine sync, Total dots, Display area (H/V) and Full screen cannot be adjusted when "1035i (HDTV)" or "1080i (HDTV)" is selected on PC SYSTEM Menu (P22). Press SELECT button at Display area icon and Display area dialog box appears. Display area Press POINT LEFT /RIGHT button(s) to adjust value and then press SELECT button. To store adjustment data. This Mode has parameters being stored. 3 Store To store adjustment parameters, move a red frame pointer to Store icon and then press SELECT button. Move a red arrow pointer to any of Mode 1 to 5 that you want to store to and then press SELECT button. Mode free To clear adjustment parameters previously set, move a red frame pointer to Mode free icon and then SELECT button. [. . . ] G Make sure a projection screen is at least 5. 3' (1. 6m) from the projector. NOTE : Moving a projector from a cool temperature location to a warm temperature location may result in moisture condensation on Projection Lens. In such an event, leave a projector OFF and wait until condensation disappears. (See "SETTING" section on page 35. ) G Check Ceiling feature. [. . . ]