User manual SANYO PLC750M

[. . . ] If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Do not stare directly into the lens as it could possibly damage your eyes. Be especially careful that children do not stare directly into the beam. G Provide appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. [. . . ] (Refer to page 26, 27. ) There is no signal input from the connected computer. Make sure the connection of the computer and the projector is set correctly. (Refer to the TROUBLESHOOTING on page 42. ) User preset adjustment in MANUAL PC ADJUSTMENT. The projector chooses proper system and displays it. PC SYSTEM MENU The SYSTEM Menu icon displays the system being selected. ­­­­ Mode 1 SVGA 1 *Mode 1 and SVGA 1 are examples. SELECT COMPUTER SYSTEM MANUALLY This projector automatically selects the PC system among those provided in this projector and PC system can also be selected manually. PC SYSTEM MENU 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to move the red frame pointer to the PC SYSTEM Menu icon. Press the POINT DOWN button to move the red arrow pointer to the system that you want to set, and then press the SELECT button. SYSTEM Menu icon Displays the system being selected. (P26, 27) NOTE G The PC SYSTEM Menu cannot be selected when the input signal is digital. 23 COMPUTER INPUT COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION 640 x 480 720 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 ­­­­­­­­ ­­­­­­­­ VGA 1 VGA 2 VGA 3 VGA 4 VGA 5 VGA 6 VGA 7 MAC LC13 MAC 13 RGB RGB SVGA 1 SVGA 2 SVGA 3 SVGA 4 SVGA 5 SVGA 6 SVGA 7 SVGA 8 SVGA 9 SVGA 10 SVGA 11 MAC 16 XGA 1 XGA 2 XGA 3 XGA 4 XGA 5 XGA 6 XGA 7 XGA 8 XGA 9 XGA 10 XGA 11 ON-SCREEN DISPLAY 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 H-Freq. (kHz) 31. 47 31. 47 31. 47 37. 86 37. 86 37. 50 43. 269 34. 97 35. 00 15. 625 15. 734 35. 156 37. 88 46. 875 53. 674 48. 08 37. 90 34. 50 38. 00 38. 60 32. 70 38. 00 49. 72 48. 36 68. 677 60. 023 56. 476 60. 31 48. 50 44. 00 63. 48 36. 00 62. 04 61. 00 H-Freq. (Hz) 59. 88 70. 09 70. 09 74. 38 72. 81 75. 00 85. 00 66. 60 66. 67 50. 00 (Interlace) 60. 00 (Interlace) ON-SCREEN DISPLAY RESOLUTION 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 870 1152 x 864 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 960 1152 x 900 1152 x 900 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1152 x 900 1280 x 1024 1280 x 1024 1400 x 1050 1280 x 960 1280 x 1024 ­­­­­­­­ ­­­­­­­­ ­­­­­­­­ ­­­­­­­­ ­­­­­­­­ ­­­­­­­­ 56. 25 60. 32 75. 00 85. 06 72. 19 61. 03 55. 38 60. 51 60. 31 51. 09 60. 51 74. 55 60. 00 84. 997 75. 03 70. 07 74. 92 60. 02 54. 58 79. 35 87. 17 (Interlace) 77. 07 75. 70 V-Freq. Press the POINT DOWN button to move the red frame pointer to the item that you want to adjust and then press the SELECT button. Fine sync PC ADJUST MENU PC ADJUST Menu icon Move the red frame pointer to the item and press the SELECT button. Adjusts an image as necessary to eliminate flicker from the display. Press the POINT LEFT/RIGHT button to adjust value. (From 0 to 31. ) Total dots The number of total dots in one horizontal period. Press the POINT LEFT/RIGHT button(s) and adjust number to match your PC image. Current mode Press the SELECT button to show the information of computer selected. Selected Mode Shows status (Stored / Free) of the selected Mode. Press the SELECT button at this icon to adjust "Clamp, " "Display area (H/V)" or set "Full screen. " Press the SELECT button at the Current mode icon to show the information of the computer connected. 26 COMPUTER INPUT Display area Selects the area displayed by this projector. Display area H Adjustment of the horizontal area displayed by this projector. Press the POINT LEFT/RIGHT button(s) to decrease/increase value and then press the SELECT button. Display area V Adjustment of the vertical area displayed by this projector. Press the POINT LEFT/RIGHT button(s) to decrease/increase value and then press the SELECT button. Full screen When this function is on, SXGA image is fully displayed at 4 : 3 aspect ratio. [. . . ] G Check the system that you select is corresponding with your computer or video equipment. G Make sure the temperature is not out of Operating Temperature (5°C ~ 35°C). G Check the COMPUTER IN 2 / MONITOR OUT terminal is set as Computer 2. "SETTING" section on page 36. ) (See the No sound. Computer 2 cannot be selected. 42 APPENDIX Problem: Remote Control does not work. G G G G Try these Solutions Check the batteries. [. . . ]