User manual SANYO PLC5600N

[. . . ] If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Be especially careful that children do not stare directly into the beam. q Do not use projectors with whiteboards that produce a very bright glare or 'hot spot'. q Take appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. [. . . ] Refer to P31. Computer 1 INPUT Menu icon Move a pointer (red arrow) to Computer 1 and press SELECT button. RGB RGB (Scart) Source Select Menu Move a pointer to RGB and press SELECT button. When connect the output (Digital/Analog) from computer to Computer 2 (DVI-I) terminal on the projector. INPUT MENU 1 2 3 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon. Press POINT DOWN button to move a red arrow pointer to Computer 2 and then press SELECT button. Move a pointer to either RGB (Digital) or RGB (Analog) and then press SELECT button. When analog signal is connected to DVI terminal, select Analog. Computer 2 INPUT Menu icon Move a pointer (red arrow) to Computer 2 and press SELECT button. RGB (Digital) RGB (Analog) Source Select Menu Move a pointer to RGB (Digital) or RGB (Analog) and press SELECT button. 22 COMPUTER INPUT SELECTING COMPUTER SYSTEM This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to "COMPATIBLE COMPUTER SPECIFICATIONS" on page 24). When selecting Computer, this projector automatically tunes to incoming signal and projects proper image without any special setting. (Some computers need setting manually. ) Note : Projector may display one of the following messages. Auto When projector cannot recognize connected signal as PC system provided in this projector, Auto PC Adjustment function operates to adjust projector and the message "Auto" is displayed on SYSTEM Menu icon. (Refer to P25. ) When image is not provided properly, manual adjustment is required. Make sure the connection of computer and a projector is set correctly. (Refer to TROUBLESHOOTING on page 42. ) PC SYSTEM MENU SYSTEM Menu icon Displays system being selected. ­­­­ D-VGA, D-SVGA or D-XGA When digital computer signal is received on DVI terminal, above message is displayed on PC SYSTEM Menu icon. SELECT COMPUTER SYSTEM MANUALLY This projector automatically selects PC system among those provided in this projector and PC system can be also selected manually. PC SYSTEM MENU 1 2 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to PC ADJUST Menu icon. Press POINT DOWN button to move a red frame pointer to the item that you want to adjust and then press SELECT button. Fine sync PC ADJUST MENU PC ADJUST Menu icon Move a red frame icon to the item and press SELECT button. Adjusts an image as necessary to eliminate flicker from the display. Press POINT LEFT/RIGHT button to adjust value. (From 0 to 31. ) Total dots The number of total dots in one horizontal period. Press POINT LEFT/RIGHT button(s) and adjust number to match your PC image. Current mode Press SELECT button to show the information of computer selected. Press SELECT button at this icon to adjust "Clamp, " "Display area (H/V)" or set "Full screen. " Selected Mode Shows status (Stored / Free) of the selected Mode. Press SELECT button at Current mode icon to show the information of computer connected. 26 COMPUTER INPUT Display area Selects area displayed with this projector. Display area H Adjustment of horizontal area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button. Display area V Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button. [. . . ] q Make sure a projection screen is at least 4. 1' (1. 2m) from the projector. NOTE : Moving a projector from a cool temperature location to a warm temperature location may result in moisture condensation on Projection Lens. In such an event, leave a projector OFF and wait until condensation disappears. (See "SETTING" section on page 36. ) q Check Ceiling feature. [. . . ]