User manual SANYO PLC220N

[. . . ] Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Troubleshooting" section in the end of this booklet. If the problem still persists, contact the dealer where you purchased the projector or the service center. Safety Precaution WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. [. . . ] (See "Troubleshooting" on page 45. ) User preset adjustment in Computer Adjustment. The projector chooses a proper system and displays it. Mode 1 SVGA 1 *Mode 1 and SVGA 1 are examples. PC system can also be selected manually if some PC systems appear on the On-Screen Menu. PC System Menu 1 2 Press the MENU button and the On-Screen Menu will appear. Press the Point Left/Right buttons to move the red frame pointer to the PC System Menu icon. Press the Point Down button to move the red arrow pointer to the system that you want to set, and then press the SELECT button. The PC System Menu icon displays the system being selected. (p27, 28) 25 Computer Input Computer Adjustment (Auto) Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to your computer. Auto PC Adjustment function can be operated as follows. 1 2 Press the MENU button and the On-Screen Menu will appear. Press the Point Left/Right button to move the red frame pointer to the PC Adjust Menu icon. Press the Point Down button to move the red frame pointer to the Auto PC Adj. This Auto PC Adjust can also be executed by pressing the AUTO PC button on the remote control. Auto PC Adj. PC Adjust Menu PC Adjust Menu icon Automatically adjusts Fine sync, Total dots, Horizontal, and Vertical for the input signal from your computer. To store adjustment data Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Move the red arrow pointer to the Mode that you want to clear and then press the SELECT button. Quit Closes the PC Adjust Menu. This Mode has parameters being stored. Press the SELECT button at the Display area icon and the Display area dialog box appears. Display area Vacant Mode shows values of "Total dots, " "Horizontal, " "Vertical, " "Display area H, " and "Display area V. " To clear adjustment data closes this dialog box. NOTE G Auto PC Adjust, Display area, Display area (H/V), and Full screen cannot be selected when "480i", "575i", "480p", "575p", "720p", "1035i", or "1080i" is selected in the PC System Menu (p25). 28 Computer Input Image Level Selection Direct Operation Select an image level among Standard, Real, Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. IMAGE button Standard Real Image 1 Image 2 Image 3 Image 4 Menu Operation 1 2 Press the MENU button and the On-Screen Menu will appear. Press the Point Left/Right button to move the red frame pointer to the Image Select Menu icon. Press the Point Down button to move the red frame pointer to the level that you want to set and then press the SELECT button. Standard Image Select Menu Image Select Menu icon Normal picture level preset on this projector. IMAGE 1~4 User preset image in the Image Adjust Menu (p30). Move the red frame pointer to the level and press the SELECT button. The level being selected. 29 Computer Input Image Level Adjustment 1 2 Press the MENU button and the On-Screen Menu will appear. Press the Point Left/Right button to move the red frame pointer to the Image Adjust Menu icon. Press the Point Down button to move the red frame pointer to the item that you want to adjust, and then press the SELECT button. [. . . ] safety standards against risk of fire, casualty and electrical hazards. The CE Mark is a Directive conformity mark of the European Community (EC). 46 Appendix Indicators and Projector Condition Check the indicators for projector condition. Indicators POWER red/green WARNING red LAMP REPLACE yellow Projector Condition The projector is OFF. (The AC power cord is unplugged. ) The projector is preparing for stand-by or the projection lamp is being cooled down. The projector cannot be turned on until cooling is completed. The projector is ready to be turned on with the POWER ON-OFF button. The projector is operating normally. The projector is in the Power management mode. The temperature inside the projector is abnormally high. When the projector is cooled down enough and the temperature returns to normal, the POWER indicator lights red and the projector can be turned on. [. . . ]