User manual SANYO PLC-XW250

[. . . ] Owner's Manual Network Set-up and Operation Wired Setting Projector Set-up and Operation This is the manual for the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed strictly. Compliance Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] *Theaccumulatedlampusetimehasreached2000hours. SNMP setting SNMP setting This projector provides a SNMP (Simple Network Management Protocol) agent function. The group which communicates information each other with SNMP is called "Community". There are two access modes in a community, Refer (read only) and Set (readwrite). The SNMP message informs the projector status called "Trap" to an administrator. Click SNMP Setting on the main menu and set up each item. PJinformation Item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enter user name of the projector etc. (optional) Place . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enter place of the projector (optional) Community name(refer) . . . . . . . Enter community name (read only). Default name is "public". Trap Item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description Community name . . . . . . . . . . . . . . . . . . . . . . Enter community name to send "Trap". Add address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enter IP address of the SNMP manager computer to receive "Trap". The SNMP agent provided with this projector is based upon MIB-2 defined by RFC1213. For private MIB information, refer to file "Mibinfo/XUPjNet. mib" in the CD-ROM. ENGLISH Chapter 3 Basic Setting and Operation Trapcheck/delete Check and delete the trap address Checking the registered trap address and deleting the address. To delete the address, tick check box in front of the IP address and click Delete button. Up to 10 trap addresses can be registered. Trapoption Trap option setting Tick check boxes in front of the condition item to send the trap. Click Set button if you tick or un-tick the check box on a page. 0 When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into " Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the remote control. Up to 99, 999 hours can be set for the time setting. Chapter 4 Controlling the Projector Describes controlling and setting of the projector by using the web browser. 4 31 ENGLISH Chapter 4 Controlling the Projector Power control and status check Click Power & Status on the main menu. By clicking ON or Standby button on the page, the power of the projector can be controlled. Confirmation window as shown in the below appears when the Standby button is pressed. Popup confirmation window Item Description PJ status Power . . . . . . . . . . . . . . . . . . . . . . . . . (ON, OFF, On starting up, On cooling down) Status . . . . . . . . . . . . . . . . . . . . . . . . . . Controls the projector power by clicking the "ON" or "Standby" button. The projector cannot be turned on while the projector is on cooling down. The web browser checks and updates the projector's condition every 30 seconds automatically. Power control and status check About projector condition Status Description Normal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power management is operating Lampfailure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lamp failure is occurring AbnormalTemperature . . . . . . . . . . . . . . . . . . . . . . . . . The temperature of the projector became too high StandbyafterAbnormalTemp. Unplug the AC cord and ask servicing to a qualified service personnel. When a security (PIN code lock) has been set on the projector, you also cannot control it through the network. [. . . ] Do not add the specified setting page because it will not be able to perform the password authentication correctly. 5 Q&A Operation Q Why can't be turned on/off with web browser?A Please make sure the settings of the projector are correct to use the projector. Please set the Standbymode of the projector's Settingmenuto "Normal". Controlling the Projector" "Power control and status check" (+pp. 32 - 33). Q Why can't I change the controls in the setting page with web browser? [. . . ]