User manual SANYO PLC-XU300

[. . . ] If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Do not stare directly into the lens as it could possibly damage your eyes. Be especially careful that children do not stare directly into the beam. G Provide appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. [. . . ] (kHz) 61. 00 35. 522 46. 90 47. 00 58. 03 60. 24 68. 68 64. 20 62. 50 63. 90 63. 34 63. 74 71. 69 81. 13 63. 98 79. 976 60. 00 61. 20 71. 40 50. 00 50. 00 63. 37 76. 97 61. 85 46. 43 63. 79 75. 00 80. 00 45. 00 33. 75 33. 75 28. 125 V-Freq. (Hz) 75. 70 86. 96 (Interlace) 58. 20 58. 30 72. 00 75. 08 75. 06 70. 40 58. 60 60. 00 59. 98 60. 01 67. 19 76. 107 60. 02 75. 025 60. 00 65. 20 75. 60 86. 00 (Interlace) 94. 00 (Interlace) 60. 01 72. 00 66. 00 86. 70 (Interlace) 60. 18 75. 08 75. 08 60. 00 60. 00 (Interlace) 60. 00 (Interlace) 50. 00 (Interlace) 77. 07 NOTE : Specifications are subject to change without notice. 23 COMPUTER INPUT PC ADJUSTMENT AUTO PC ADJUSTMENT Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your computer. Auto PC Adj. 1 2 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to PC ADJUST Menu icon. button on Remote Control Unit. PC ADJUST MENU PC ADJUST Menu icon Store adjustment parameters. Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, the setting can be done just by selecting Mode in PC SYSTEM Menu (P22). Refer to step 3 of MANUAL PC ADJUSTMENT section (P26). Move a red frame pointer to AUTO PC Adj. icon and press SELECT button. NOTE G Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment function. When the image is not provided properly through this function, manual adjustments are required. (Refer to page 25, 26. ) G Auto PC Adjustment function cannot be operated when "RGB, " "720p (HDTV), " "1035i (HDTV)" or "1080i (HDTV)" is selected on PC SYSTEM Menu (P22). 24 COMPUTER INPUT MANUAL PC ADJUSTMENT This projector can automatically tune to the display signals from most personal computers currently distributed. Reset Reset all adjust parameters on adjustment dialog box to previous figure. To clear adjustment data. Vacant Mode Shows values of "Total dots, " "Horizontal, " "Vertical, " "Display area H, " and "Display area V. " Close this dialog box. 26 COMPUTER INPUT PICTURE IMAGE ADJUSTMENT IMAGE LEVEL SELECT (DIRECT) Select image level among Standard, Real, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE button on Top Control or on Remote Control Unit. This adjustment is suitable for providing better image in brighter place. IMAGE 1~4 User preset picture adjustment in IMAGE ADJUST Menu (P28, 29). IMAGE button Standard Real Image 1 Image 2 Image 3 Image 4 IMAGE LEVEL SELECT (MENU) 1 2 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to IMAGE SELECT Menu icon. Press POINT DOWN button to move a red frame pointer to the level that you want to set and then press SELECT button. Standard IMAGE SELECT MENU IMAGE SELECT Menu icon Normal picture adjustment preset on this projector. This adjustment is suitable for providing better image in brighter place. IMAGE 1~4 User preset picture adjustment in IMAGE ADJUST Menu (P28, 29). The level being selected. Move a red frame pointer to the level and press SELECT button. 27 COMPUTER INPUT IMAGE LEVEL ADJUSTMENT 1 2 Press MENU button and ON-SCREEN MENU will appear. [. . . ] G Wait 90 seconds after a projector is turned OFF before turning the projector back on. NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as follows: 1. After 90 seconds, READY indicator lights green again and a projector may be turned on by pressing Power ON-OFF button. (See "TURNING ON/OFF PROJECTOR" section on page 19. ) G Check Projection Lamp. [. . . ]