User manual SANYO PLC-XP57L

[. . . ] Multimedia Projector MODEL PLC-XP57L Projection lens is optional. Owner's Manual TO THE OWNER Before operating this projector, read this manual thoroughly and operate the projector properly. Operating the projector properly enables you to manage those features and maintain it in better condition for a considerable time. Improper operation may result in not only shortening the product life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Troubleshooting" section in the end of this booklet. [. . . ] Press the POINT LEFT/RIGHT buttons to adjust the number to match your PC image. Selected Mode Shows status (Stored/Free) of the selected Mode. Position H Press the POINT LEFT/RIGHT buttons to adjust the horizontal picture position. Position V Press the POINT LEFT/RIGHT buttons to adjust the vertical picture position. Display area H Adjusts the horizontal area displayed by this projector. Press the POINT LEFT/RIGHT buttons to decrease/increase the value. Press the SELECT button at the Current mode icon to show information of the computer connected. Press the SELECT button at this icon to adjust "Clamp, " "Display area H, " or "Display area V. " Current mode 27 COMPUTER INPUT Reset To reset the adjusted parameters, select Reset and press the SELECT button. Mode free To clear adjusted parameters previously set, move the red frame pointer to the Mode free icon and then press the SELECT button. Move the red arrow pointer to a Mode that you want to clear and then press the SELECT button. Store To store the adjusted parameters, move the red frame pointer to the Store icon and then press the SELECT button. Move the red arrow pointer to any of the Mode 1 to 10 in which you want to store the parameters and then press the SELECT button. Quit Exit the PC ADJUST Menu. Vacant Close this dialog box. To store adjustment data. This Mode has parameters being stored. Shows the values of "Total dots, " "Position H, " "Position V, " "Display area H, " and "Display area V. " A confirmation box appears and then select [Yes]. To clear adjustment data. Close this dialog box. A confirmation box appears and then select [Yes]. 28 COMPUTER INPUT PICTURE IMAGE SELECT IMAGE LEVEL SELECT DIRECT OPERATION Select an image level from among Standard, Real, and Image 1 to Image 10 by pressing the IMAGE button on the top control or on the remote control. Standard Normal picture level preset on this projector. (p. 3537) IMAGE button Standard Real Image 1 Image 10 MENU OPERATION 1 2 Press the MENU button to display the On-Screen Menu. Press the POINT LEFT/RIGHT buttons to move the red frame pointer to the IMAGE SELECT Menu icon. Press the POINT UP/DOWN buttons to move the red frame pointer to the desired level and then press the SELECT button. Standard IMAGE SELECT MENU IMAGE SELECT Menu icon Normal picture level preset on this projector. (p. 3537) Move the red frame pointer to a level and press the SELECT button. 29 COMPUTER INPUT PICTURE SCREEN ADJUSTMENT PICTURE SCREEN SELECT This projector has a picture screen resize function, which enables you to display the desirable image size. 1 2 Press the MENU button to display the On-Screen Menu. Press the POINT LEFT/RIGHT buttons to move the red frame pointer to the SCREEN Menu icon. Press the POINT UP/DOWN buttons and move the red frame pointer to the desired function and then press the SELECT button. Normal SCREEN MENU SCREEN Menu icon Move the red frame pointer to a function and press the SELECT button. Provides the image to fit the screen size. Wide Provides the image to fit the wide video aspect ratio (16:9) by expanding the image width uniformly. This function can be used to provide the squeezed video signal at 16:9. Digital zoom + When the Digital zoom + is selected, the On-Screen Menu disappears and "D. The Panning function can work only when the image is larger than the screen size. [. . . ] The projector cannot be turned on until the cooling process is completed. ) The lamp cannot light up. (The lamp has been cooled down enough and the projector is in stand-by mode and ready to be turned on with the POWER ON-OFF button. ) The projection lamp reaches its end of life. The indicator is turned off. · · · on · · · blinking · · · dim · · · off *When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow, replace the projection lamp with a new one promptly. [. . . ]