User manual SANYO PH-DTA100
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SANYO PH-DTA100. We hope that this SANYO PH-DTA100 user guide will be useful to you.
Manual abstract: user guide SANYO PH-DTA100
Detailed instructions for use are in the User's Guide.
[. . . ] If this equipment causes harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. [. . . ] The replacement must be carried out by a qualified service personnel.
PJ-NET ORGANIZER OWNER'S MANUAL [PH-DTA100 Series]
ENGLISH
Chapter 4 Controlling the Projector
Projector information
This page is to display the basic information of the projector status. Click Information on the main menu.
Items
Description
Input. . . . . . . . . . . . . . . . . . . . . . . . . Displays selected input and source. Signal . . . . . . . . . . . . . . . . . . . . . . . Input signal status (Yes, No) Screen . . . . . . . . . . . . . . . . . . . . . Displays screen mode. Security . . . . . . . . . . . . . . . . . . Displays the security (PIN code lock) status (Yes, No)
Click this button to update the information
0
Projector information
Indication of the lamp status
Icon display/background Status
White-Yellow/Blue
Lamp on (Normal) Lamp on (Lamp is being used over a specified use time, replace lamp immediately) Lamp off (Normal) Lamp off (Lamp is being used over a specified use time, replace lamp immediately) Lamp failure (Lamp failure, check lamp condition) Lamp failure (Lamp failure and lamp is being used over a specified use time, replace lamp immediately)
White-Yellow/Red
Gray/Blue
Gray/Red
Red/Blue with X
Red/Red with X
Items
Description
PJtime. . . . . . . . . . . . . . . . . . . . . OFF No timer setting.
PJ-NET ORGANIZER OWNER'S MANUAL [PH-DTA100 Series]
1
ENGLISH
Chapter 4 Controlling the Projector
Multi-control
Controlling and setting the multi-projectors
This function enables you to control the multiple projectors equipped with the network units that are connected to the network. Click Multi Control on the main menu to display the control page.
Note:
To control the multiple projectors, each projector must have the same Network PIN code.
Example of multi control
PJ1 PJ2 PJ3 PJ4
PC6 PC5
Select Input2 for PJ1 to PJ4.
PC4
Multi-control
Start/stop the multi control
To start or stop controlling the multi-projectors, click Multi control setting menu and select ON or OFF.
Multi control setting
OFF . . . . . . . . Stops multi control function ON . . . . . . . . . . These items of menu are linked to the main menu.
Switches on and off the multi-control function
The multi controllable menus are "Power & Status", "PC adjustment", "Control", "Setting", "E-mail setting", "Timer", "SNMP setting" and "Network Viewer". Click each menu and perform setting and adjustment.
The word "MULTI CONTROL" appears on the each control
page while the multi control is operating.
This shows the multi control is operating now.
PJ-NET ORGANIZER OWNER'S MANUAL [PH-DTA100 Series]
ENGLISH
Chapter 4 Controlling the Projector
Register the projector
To use the multi control function, register the IP address of the projector you intend to control. Click PJ registration sub menu tab and set the IP address, Memo and Multi control item, then click Set button.
Items Description
IPaddress . . . . . . . . . . . . . Enter IP address of the projector to control Memo . . . . . . . . . . . . . . . . . . . . . . Enter projector name or installed location etc.
Multi control item
Control . . . . . . . . . . . . . . Displaying the images
Confirmation of registered projector
To check the registered information, click Conf. The registered information of the projector is listed as the below.
* The word "none" is displayed if not using the "Memo" function.
* When you click on a listed IP address, the login page for the selected projector will be displayed with a new window.
IP address
Status
Memo
Page no.
Click here to close the sub menu Conf. Set the display time periods and repeat times for the auto image display. When clicking Start button, the registered projectors start playing back the auto image display in sequential.
For further information of the Auto display, see "Using the net-
work viewer function". (+p. 98)
This is effective only if the multi control item of the registered
projector sets to either "Control&Image" or "Image".
PJ-NET ORGANIZER OWNER'S MANUAL [PH-DTA100 Series]
7
ENGLISH
Chapter 4 Controlling the Projector
Chapter 5 Network Capture
Network Capture is a function to display the screen image of the computer via the network. - Real Time Capture - Network Communication
5
PJ-NET ORGANIZER OWNER'S MANUAL [PH-DTA100 Series]
69
ENGLISH
Chapter 5 Network Capture
About Network Capture function
The Network Capture is a function to project the screen images of the computer which has a Network Capture 3 software by the projector through the network. This function has 2 kinds of mode as the below.
- Real Time Capture (+p. 2)
A function to display the screen image of the computer by the projector through the network in real time.
- Network Communication (+p. )
This mode is to communicate by sharing the capture image of a computer with multiple computers and a projector. User can draw the text and figure on the captured image by using a drawing tool.
Up to 30 computers can be registered. The Network Capture function cannot be used when using the Network Viewer function. The
Real Time Capture and Network Communication mode cannot be used at the same time.
Launching the Network Capture 3
After installing the Network Capture 3 software, the shortcut icon is copied into the "Startup" folder. When you boot the computer, the Network Capture software also starts and its icon stays on the task bar. If the icon is not appeared on the task bar, the Network Capture 3 software is not starting. Click "Network Capture 3" from "Start" - "All the Programs" - "Network Viewer & Capture 3" menu to launch it manually. [. . . ] By registering the projector name and IP address with the DNS server, it can be accessed with the nickname from the any computer referred to the DNS server. Please consult your network administrator.
Q A
How many numbers of the E-mail address can I register in the E-mail setting page.
You can register up to 10 addresses.
11
Q&A
Q A
Why am I not receiving E-mail alert messages?
Make sure that the registered E-mail address and SMTP server address are correct. If the SMTP server is located in your LAN (Local Area network), the address should be set to the SMTP server in your LAN. The SMTP server located outside of your LAN may not be available for security reason. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SANYO PH-DTA100
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SANYO PH-DTA100 will begin.