User manual SANYO PDP42H1A

[. . . ] If the problem still persists, contact the sales dealer where you purchased the Plasma Monitor or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This Plasma Monitor should be set in the way indicated. Take appropriate space on the top, sides and rear of the Plasma Monitor cabinet for allowing air circulation and cooling the Plasma Monitor. If the Plasma Monitor is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Heat build-up can reduce the life of your Plasma Monitor, and can also be dangerous. [. . . ] (Refer to "CONNECTING TO VIDEO EQUIPMENT" on Page 13. ) AV 1 AV 2 AV 3 COMPONENT INPUT Select "Component1" or "Component2" by pressing the COMPONENT button on the Remote Control Unit. (Refer to "CONNECTING TO COMPONENT VIDEO EQUIPMENT" on Page 14. ) Component 1 Component 2 PC/DVI-D INPUT Select "PC" or "DVI-D" by pressing the PC/DVI-D button on the Remote Control Unit. (Refer to "CONNECTING TO COMPUTER" on Page 15. ) PC DVI-D VIDEO button NOTE : By pressing the STATUS button on the Remote Control Unit, the selected input source, ECO mode indication (if the Eco mode is set) and OFF TIMER's remaining time (if the OFF TIMER is set) will be displayed for 5 seconds. INPUT VIDEO COMPONENT ON-OFF PC/DVI-D COMPONENT button VOLUME OFF TIMER MUTE WIDE PICTURE MOVE UP PC/DVI-D button FRONT CONTROL OPERATION Choose either input mode by pressing INPUT button on the Plasma Monitor's Front Control. STATUS MOVE DOWN MENU SURROUND AUTO PC POWER AV 1 AV 2 AV 3 4 Component 1 MENU OK INPUT ­ VOLUME + Component 2 INPUT button PC DVI-D 21 BASIC OPERATION PICTURE IMAGE LEVEL SELECT VIDEO/COMPONENT MODE Select an image level among Dynamic, Natural, Cinema and Memory by pressing the PICTURE button on the Remote Control Unit. Dynamic Natural Cinema Memory In Video / Component mode VIDEO COMPONENT ON-OFF PC/DVI-D VOLUME OFF TIMER MUTE WIDE PICTURE MOVE UP PICTURE button OK STATUS MOVE DOWN MENU SURROUND AUTO PC POWER PC/DVI-D MODE Select an image level among Graphic, Standard, Text and Memory by pressing the PICTURE button on the Remote Control Unit. Graphic Standard Text Memory In PC / DVI-D mode 22 BASIC OPERATION OPERATING ON-SCREEN MENU You can control and adjust this Plasma Monitor through the On-Screen Menu. Refer to the following pages to operate each VIDEO COMPONENT ON-OFF adjustment on the On-Screen Menu. PC/DVI-D VOLUME BUTTONS FOR ON-SCREEN MENU OPERATION REMOTE CONTROL UNIT CURSOR ed button CURSOR 7 8 button STATUS button WIDE OFF TIMER MUTE OK button PICTURE MOVE UP OK STATUS MOVE DOWN MENU MENU button SURROUND AUTO PC POWER ON FRONT CONTROL OK button MENU button MENU OK INPUT ­ VOLUME + CURSOR 7 8 button CURSOR ed button FLOW OF ON-SCREEN MENU OPERATION 1 2 3 4 5 Press the MENU button on the Remote Control Unit or the Front Control and the On-Screen Menu will appear. Press the ed buttons to select the menu that you want to adjust, and then press the OK button. Adjust the item by pressing the 7 8 buttons. MAIN MENU Picture adjustment Sound adjustment Screen adjustment Picture setup Initial setup PC mode adjustment Screen saver Information 78 Select OK OK STATUS Return M E N U Exit Press the STATUS button to return to the previous menu display. Press the MENU button to close the On-Screen Menu. SUB MENU Picture adjustment Contrast Brightness Color Tint Sharpness Noise reduction 62 32 32 0 0 Off 78 Select OK OK STATUS Return M E N U Exit 23 BASIC OPERATION ON SCREEN MENU TREE Picture adjustment MENU Picture adjustment Contrast Brightness 62 32 32 0 0 Off (P26) Picture adjustment Sound adjustment Screen adjustment Picture setup Initial setup PC mode adjustment Screen saver Information Color Tint Sharpness Noise reduction Select OK MENU OK Exit STATUS Return Contrast Brightness Color Tint Sharpness Noise reduction (P27) Sound adjustment OK OK Sound adjustment 78 Select STATUS Return M E N U Exit 78 Treble Bass Balance BBE 0 0 0 Off Select 78 MENU Adjust Exit STATUS Return Treble Bass Balance BBE (P28) Screen adjustment Screen adjustment Vertical Horizontal Move 1 1 1 78 Vertical Horizontal Move Adjust Exit 78 Select 78 MENU STATUS Return Picture setup Picture setup (P34) Dynamic AI/Light sensor ECO mode Color temperature Flesh tone Cinema auto AI Off Normal Off On 78 Dynamic AI/ Light sensor ECO mode Color Temperature Flesh tone Cinema auto Select 78 Select STATUS Return M E N U Exit To be continued to next page 24 BASIC OPERATION MENU Initial setup Picture adjustment Sound adjustment Screen adjustment Picture setup Initial setup PC mode adjustment Screen saver Information 78 Select 78 (P35) English HDCP Off Off Setup Initial setup Language DVI setup Start mode No operation shut off timer Reset Language DVI setup Start mode No operation shut off timer Reset Select STATUS Return M E N U Exit 78 Select OK OK STATUS Return M E N U Exit PC mode adjustment PC mode adjustment Auto setup Clock Phase Position Power save (P30-31) Select OK OK STATUS Return M E N U Exit Auto setup Clock Phase Position Power save (P36-37) Screen saver Screen saver Pic rotation Cycle time Dot White pattern Display time Side bar On 30 Min 20 Off 10 Min Off 78 Select 78 MENU Select Exit Picture rotation Cycle time Dot White pattern Display time Side bar STATUS Return Information Information Temperature Cooling fan Signal OK OK VIDEO 78 (P37) 525i(480i) STATUS Return M E N U Exit 25 BASIC OPERATION PICTURE ADJUSTMENT 1 2 3 Press the MENU button and the On-Screen Menu will appear. Press the ed buttons to select an item that you want to adjust, and then press the OK button. Adjust each value by pressing the 7 8 buttons. MENU Picture adjustment Contrast Brightness Color Tint Sharpness Noise reduction 62 32 32 0 0 Off NOTE : The adjusted Video and Computer values are memorized individually. To return to the previous menu, press the STATUS button after the adjustment is completed. NOTE : While the Auto setup is working, pressing the MENU button finishes adjustment immediately and the message "Auto setup" will disappear. In the following cases, the Plasma Monitor may not adjust itself with the "Auto setup" function: 1) If the picture is not displayed fully on the screen. 2) When a contrast picture, such as an outdoor scene, is displayed on the screen. Depending on the signal and computer's configuration, "Auto setup" function cannot be performed properly. In this case, adjust "Clock", "Phase" and "Position" manually. PC mode adjustment Auto setup Clock Phase Position Power save 78 Select OK OK STATUS Return M E N U Exit PC mode adjustment ON-OFF VIDEO COMPONENT PC/DVI-D Auto setup VOLUME Proceed 7 8 WIDE OFF TIMER Proceed STATUS Return M E N U Exit PICTURE MOVE UP MUTE Direct operation The Auto setup function can be operated directly by pressing the AUTO PC button on the Remote Control Unit. Press the AUTO PC button on the Remote Control Unit to start the Auto setup and then the message "Now adjusting" will be displayed. To return to the previous menu, press the STATUS button after the adjustment is completed. OK STATUS MOVE DOWN MENU SURROUND AUTO PC POWER ON OFF AUTO PC button Clock Adjust when Vertical noise lines are observed. (Horizontal width will be changed by the adjustment. ) Adjust with the 78 buttons. Clock 1344 30 COMPUTER MODE Phase Adjust when Horizontal noise lines are observed. Adjust with the 78 buttons. NOTE : This adjustment will be required when the displayed image is unclear or flickering. Phase 0 Position Adjusts the screen position. Adjust with the ed and 78 buttons. Position 7ed8 Power save Enables or disables the Power save function. Enable the Power save function by choosing "On" with the 78 buttons. NOTE : The Power save function automatically reduces the Plasma Monitor's power consumption if the computer is not operated for a certain period of time. [. . . ] Internal temperature is too high. " When this message is displayed, the internal temperature of the Plasma monitor exceeds normal. The Plasma Monitor will be turned off automatically after displaying this message for 10 seconds. When the Plasma Monitor has been cooled down and the temperature returns to normal, the Plasma Monitor can be turned on again by pressing the POWER button. If the message is displayed frequently, contact sales dealer where you purchased the Plasma Monitor or the service center. 39 APPENDIX AUTO POWER OFF When a trouble is detected in the Plasma Monitor, the protection function works and turn the Plasma Monitor off automatically. [. . . ]