User manual SANYO PDP32H1ENV

[. . . ] If the problem still persists, contact the sales dealer where you purchased the Plasma Monitor or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This Plasma Monitor should be set in the way indicated. Take appropriate space on the top, sides and rear of the Plasma Monitor cabinet for allowing air circulation and cooling the Plasma Monitor. If the Plasma Monitor is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Heat build-up can reduce the life of your Plasma Monitor, and can also be dangerous. [. . . ] It expands the width and height of the image and makes it look natural. Zoom Provides an image to fit the screen size (16 : 9 aspect ratio) by expanding the width and height of the image uniformly. This function can be used to project a letter box mode picture (4 : 3 aspect picture with black bar on the top and bottom edges) at a wide video aspect ratio of 16 : 9. Zoom (Caption-IN) Provides an image including a caption to fit the screen size (16 : 9 aspect ratio) by expanding the width and height of the image uniformly. SURROUND AUTO PC POWER FREEZE! FREEZE! Full Provides an image to fit width of screen by expanding image width uniformly. This function can be used for enjoying a squeezed video signal with wide video aspect ratio of 16 : 9 screen. When your video equipment (such as DVD) has 16 : 9 output mode, select 16 : 9 and select Full to provide better quality. Normal Provides an image at a normal video aspect ratio of 4 : 3. 20 BASIC OPERATION SELECTING INPUT SOURCE VIDEO INPUT Select either "AV1" or "AV2" or "AV3" by pressing the VIDEO button on the Remote Control Unit. (Refer to "CONNECTING TO VIDEO EQUIPMENT" on Page 13. ) AV 1 AV 2 AV 3 COMPONENT INPUT Select "Component1" or "Component2" by pressing the COMPONENT button on the Remote Control Unit. (Refer to "CONNECTING TO COMPONENT VIDEO EQUIPMENT" on Page 14. ) Component 1 Component 2 PC/DVI-D INPUT Select "PC" or "DVI-D" by pressing the PC/DVI-D button on the Remote Control Unit. (Refer to "CONNECTING TO COMPUTER" on Page 15. ) PC DVI (PC) VIDEO button NOTE : By pressing the STATUS button on the Remote Control Unit, the selected input source, ECO mode indication (if the Eco mode is set) and OFF TIMER's remaining time (if the OFF TIMER is set) will be displayed for 5 seconds. INPUT VIDEO COMPONENT ON-OFF PC/DVI-D PC/D COMPONENT button VOLUME OLUME OFF TIMER MUTE WIDE PICTURE MOVE UP PC/DVI-D button FRONT CONTROL OPERATION Choose either input mode by pressing INPUT button on the Plasma Monitor's Front Control. STATUS MOVE DOWN MENU SURROUND AUTO PC POWER AV 1 AV 2 AV 3 4 Component 1 MENU OK INPUT ­ VOLUME + Component 2 INPUT button PC DVI (PC) 21 BASIC OPERATION PICTURE IMAGE LEVEL SELECT VIDEO/COMPONENT MODE Select an image level among Dynamic, Natural, Cinema and Memory by pressing the PICTURE button on the Remote Control Unit. Dynamic Natural Cinema Memory In Video / Component mode VIDEO COMPONENT ON-OFF PC/DVI-D PC/D VOLUME OLUME OFF TIMER MUTE WIDE PICTURE MOVE UP PICTURE button OK STATUS MOVE DOWN MENU TUS SURROUND AUTO PC POWER PC/DVI-D MODE Select an image level among Graphic, Standard, Text and Memory by pressing the PICTURE button on the Remote Control Unit. Graphic Standard Text Memory In PC / DVI-D mode 22 BASIC OPERATION OPERATING ON-SCREEN MENU You can control and adjust this Plasma Monitor through the On-Screen Menu. (Some computers need manual setting. ) If the Monitor may not be able to display a proper image, the following messages will be displayed. Out of scan range When the Plasma Monitor detects any signal out of the system formats provided in the Compatible Computer Specifications on page 32 of this manual, the message "Out of scan range" will be displayed for a few seconds. Make sure the connection of the computer and the Plasma Monitor. No signal 29 COMPUTER MODE PC ADJUSTMENT PC MODE ADJUSTMENT "PC mode adjustment" menu is provided to adjust "Clock", "Phase", "Position" and "Power save" to conform to your computer. These functions can be operated as follows: 1 2 3 4 Press the MENU button and the On-Screen Menu will appear. Press the ed buttons to select "PC mode adjustment" menu and then press the OK button. Press the ed buttons to select an item that you want to adjust, and then press the OK button. The selected item will appear. PC MODE ADJUSTMENT MENU Picture adjustment Sound adjustment Screen adjustment Picture setup Initial setup PC mode adjustment Screen saver Information 78 Adjust each value by pressing the 78 buttons. Select OK OK STATUS Return M E N U Exit Auto setup "Auto setup" function is provided to automatically adjust "Clock", "Phase" and "Position" to conform to your computer. "Auto setup" can be started by pressing the the 8 button, and the message "Now adjusting" will be displayed. To return to the previous menu, press the STATUS button after the adjustment is completed. NOTE : While the Auto setup is working, pressing the MENU button finishes adjustment immediately and the message "Auto setup" will disappear. In the following cases, the Plasma Monitor may not adjust itself with the "Auto setup" function: 1) If the picture is not displayed fully on the screen. 2) When a contrast picture, such as an outdoor scene, is displayed on the screen. Depending on the signal and computer's configuration, "Auto setup" function cannot be performed properly. [. . . ] . . . " is displayed. Afterimages (ghosts) Do not display the same image on screen for a long period of time. Afterimage may disappear gradually. 38 APPENDIX Problem: There are tiny black points and/or bright points on the PDP. (No power) Try these Solutions There may be some tiny black points and/or bright points on the PDP (Plasma Display Panel). These points are normal. When the Plasma Monitor has some trouble, self diagnose function activates. (P40) WARNING : High voltages are used to operate this Plasma Monitor. [. . . ]