User manual SANYO PDP-42H2A

[. . . ] Multimedia Plasma Monitor MODEL PDP-42H2A Owner's Manual TO THE OWNER Before operating this Plasma Monitor, read this manual thoroughly and operate the Plasma Monitor properly. Operating the Plasma Monitor properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your Plasma Monitor seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Trouble-shooting" section of the end of this booklet. [. . . ] Press the ed buttons to select the menu that you want to adjust, and then press the OK button. Adjust the item by pressing the 7 8 buttons. MAIN MENU Picture adjustment Sound adjustment Screen adjustment Picture setup Initial setup PC mode adjustment Screen saver Information 78 Select OK OK STATUS Return M E N U Exit Press the STATUS button to return to the previous menu display. Press the MENU button to close the On-Screen Menu. SUB MENU Picture adjustment Contrast Brightness Color Tint Sharpness Noise reduction 62 32 32 0 0 Off 78 Select OK OK STATUS Return M E N U Exit 23 BASIC OPERATION ON SCREEN MENU TREE Picture adjustment MENU Picture adjustment Contrast Brightness 62 32 32 0 0 Off (P26) Picture adjustment Sound adjustment Screen adjustment Picture setup Initial setup PC mode adjustment Screen saver Information Color Tint Sharpness Noise reduction Select OK MENU OK Exit STATUS Return Contrast Brightness Color Tint Sharpness Noise reduction (P27) Sound adjustment OK OK Sound adjustment 78 Select STATUS Return M E N U Exit 78 Treble Bass Balance BBE 0 0 0 Off Select 78 MENU Adjust Exit STATUS Return Treble Bass Balance BBE (P28) Screen adjustment Screen adjustment Vertical Horizontal Move 1 1 1 78 Vertical Horizontal Move Adjust Exit 78 Select 78 MENU STATUS Return Picture setup Picture setup (P34) Dynamic AI/Light sensor ECO mode Color temperature Flesh tone Cinema auto AI Off Normal Off On 78 Dynamic AI/ Light sensor ECO mode Color Temperature Flesh tone Cinema auto Select 78 Select STATUS Return M E N U Exit To be continued to next page 24 BASIC OPERATION MENU Initial setup Picture adjustment Sound adjustment Screen adjustment Picture setup Initial setup PC mode adjustment Screen saver Information 78 Select 78 (P35) English HDCP Off Off Setup Initial setup Language DVI setup Start mode No operation shut off timer Reset Language DVI setup Start mode No operation shut off timer Reset Select STATUS Return M E N U Exit 78 Select OK OK STATUS Return M E N U Exit PC mode adjustment PC mode adjustment Auto setup Clock Phase Position Power save (P30-31) Select OK OK STATUS Return M E N U Exit Auto setup Clock Phase Position Power save (P36-37) Screen saver Screen saver Pic rotation Cycle time Dot White pattern Display time Side bar On 30 Min 20 Off 10 Min Off 78 Select 78 MENU Select Exit Picture rotation Cycle time Dot White pattern Display time Side bar STATUS Return Information Information Temperature Cooling fan Signal OK OK VIDEO 78 (P37) 525i(480i) STATUS Return M E N U Exit 25 BASIC OPERATION PICTURE ADJUSTMENT 1 2 3 Press the MENU button and the On-Screen Menu will appear. Press the ed buttons to select an item that you want to adjust, and then press the OK button. Adjust each value by pressing the 7 8 buttons. MENU Picture adjustment Contrast Brightness Color Tint Sharpness Noise reduction 62 32 32 0 0 Off NOTE : The adjusted Video and Computer values are memorized individually. Noise reduction cannot be adjusted when the input mode is "PC" or "DVI-D". 78 Select OK OK STATUS Return M E N U Exit Select the item and then press the OK button. Picture adjustment Contrast 63 78 Select 78 Adjust STATUS Return M E N U Exit Contrast Press the 7 button to decrease contrast, and the 8 button to increase contrast. Contrast 63 Brightness Press the 7 button to adjust image darker, and the 8 button to adjust brighter. Brightness 31 Color Press the 7 button to lighter color, and the 8 button to darker color. Color 31 Tint Press the 7 or 8 button to obtain proper color. Tint 0 Sharpness Press the 7 button to soften the image, and the 8 button to sharpen the image. Sharpness 8 Noise reduction Press the 7 or 8 button to select "On" or "Off". Noise reduction On 26 BASIC OPERATION SOUND ADJUSTMENT VOLUME Press the VOLUME (+/­) button(s) on the Remote Control Unit or the Front Control to adjust volume. Press the VOLUME (+) button to increase volume, and (­) button to decrease. (green) Indicates the roughly level of volume. 9 MUTE Press the MUTE button on the Remote Control Unit to mute sound. To restore sound to its previous level, press the MUTE button again or press the Volume (+/­) button(s). Mute 9 (red) VIDEO COMPONENT ON-OFF SURROUND Press the SURROUND button on the Remote Control Unit to set the 3D surround function on/off. PC/DVI-D PC/DVI-D VOLUME VOLUME button WIDE OFF TIMER MUTE PICTURE MOVE UP MUTE button OK STATUS ST TUS MOVE DOWN MENU SURROUND button SURROUND AUTO PC UTO POWER ON SOUND ADJUSTMENT SOUND MENU Sound adjustment 1 2 3 Press the MENU button and the On-Screen Menu will appear. Press the ed buttons to select "Sound" menu and then press the OK button. Press the ed buttons to select an item that you want to adjust and make adjustment by pressing the 78 buttons. Treble Bass Balance BBE 0 0 0 Off 78 Select 78 Adjust STATUS Return M E N U Exit Treble Press the 7 button to decrease high frequency sound, and the 8 button to increase high frequency sound. Bass Press the 7 button to decrease low frequency sound, and the 8 button to increase low frequency sound. Balance Adjusts the volume balance of the left and right speakers. R BBE 3D SURROUND 9 The on-screen display when BBE is set "On" or "Bass" and Surround "On". Mach3Bass BBE Set "On" to provide "BBE-ON" sound, and set "Bass" to provide "BBE Mach 3 Bass-ON" sound. BBE and BBE symbol are registered trademarks of BBE Sound, Inc. 27 BASIC OPERATION SCREEN ADJUSTMENT ADJUSTING WIDE IMAGE SCREEN ADJUST MENU Screen adjustment 1 2 3 Press the MENU button and the On-Screen Menu will appear. Press the ed buttons to select "Screen adjustment" menu and then press the OK button. Press the ed buttons to select "Vertical" "Horizontal" or "Move", and adjust image by pressing the 78 buttons. Vertical Horizontal Move 1 1 1 78 Select 78 Adjust Adjustment data is memorized in each wide image mode. Horizontal Adjustment of horizontal expand proportion on both sides of the image. Move Adjustment of vertical position of the image. STATUS Return M E N U Exit NOTE : "Vertical", "Horizontal" and "Move" may not be adjusted depending on the screen size selected. "Vertical", "Horizontal" and "Move" can not be adjusted when the input signal is PC or DVI-D. VIDEO COMPONENT ON-OFF UP/DOWN PICTURE PC/DVI-D VOLUME OFF TIMER MUTE To directly move up/down the image vertically, press the MOVE UP / MOVE DOWN buttons. NOTE : Up and down picture function can work only when the input signal mode is "AV1", "AV2", "AV3", "Component1" or "Component2" and the image mode is "Natural wide", "Zoom" or "Zoom(Caption-IN)". WIDE PICTURE MOVE UP MOVE UP button MOVE DOWN button OK STATUS MOVE DOWN MENU TUS SURROUND AUTO PC POWER POWER Move +3 28 COMPUTER MODE SELECTING INPUT SOURCE REMOTE CONTROL OPERATION Select "PC" or "DVI-D" by pressing the PC/DVI-D button on the Remote Control Unit. PC DVI (PC) FRONT CONTROL OPERATION Select "PC" or "DVI-D" by pressing the INPUT button on the Front Control of the Plasma Monitor. (Refer to P21) SELECTING COMPUTER SYSTEM This Plasma Monitor automatically tunes to most different types of computers based on VGA, SVGA or XGA (refer to "COMPATIBLE COMPUTER SPECIFICATIONS" on page 32). When selecting PC for the input mode, this Plasma Monitor automatically detects the incoming signal and displays a proper image without any special setting. (Some computers need manual setting. ) If the Monitor may not be able to display a proper image, the following messages will be displayed. Out of scan range When the Plasma Monitor detects any signal out of the system formats provided in the Compatible Computer Specifications on page 32 of this manual, the message "Out of scan range" will be displayed for a few seconds. [. . . ] Do not attempt to open the cabinet. If the problem still persists after following all operating instructions, contact the sales dealer where you purchased the Plasma Monitor or the service center. We will advise you how to obtain service. FUNCTIONS OF PRODUCT SAFETY FEATURES For protecting product safety, protection features provided inside the Plasma Monitor. Each feature operating as follows ; COOLING FAN When the temperature of inside the Plasma Monitor becomes high, the cooling fans start operating automatically to cool down the Plasma Monitor. The fan's running speed is changed according to the inside temperature of the Plasma Monitor. [. . . ]