User manual SANYO PDP-42H1

[. . . ] THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED. Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC will repair or replace (at its option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail. [. . . ] THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. If the video product does not operate normally by following the operating instructions, adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation. When the video product exhibits a distinct change in performance -- this indicates a need for service. 6A. Video monitor or equipment and cart combinations should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the equipment and cart combination to overturn. 7. VENTILATION -- Slots and openings in the cabinet and the back or bottom are provided for ventilation, and to ensure reliable operation of the video monitor or equipment and to protect it from overheating. The openings should never be blocked by placing the video monitor or equipment on a bed, sofa, rug, or other similar surface. Video monitor or equipment should never be placed near or over a radiator or heat register. Video monitor or equipment receiver should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided. 8. POWER SOURCES -- Video monitor or equipment should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your video monitor or equipment dealer or local power company. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling. SERVICE This unit is a precision instruments and if treated with care, will provide years of satisfactory performance. TITLE : Lets you display the title name (8 characters) on the screen for each component which is connected to the terminals at the rear of the monitor. VERSION : This item is for display only and cannot be changed. Underscan/overscan select button (SCAN) for Model 8618 only The initial setting is for the normal screen (overscan). If the SCAN button is pressed, the screen will become smaller (underscan) than the normal screen. Change this setting in cases such as when screen display characters are missing. If the SCAN button is pressed once more, the normal screen is displayed again. 7 Monitor A selector button (A) When this button is pressed, the audio and video input changes to the component which is connected to the A terminals at the rear of the monitor. 8 Monitor B selector button (B) When this button is pressed, the audio and video input changes to the component which is connected to the B terminals at the rear of the monitor. 9 Monitor Y/C selector button (Y/C) When this button is pressed, the audio and video input changes to the component which is connected to the Y/C terminals at the rear of the monitor. F Power indicator (POWER) Lights when the power is on. G Power button (POWER) 4 Press this button to turn the power on and off. PARTS NAMES Rear Panel 2 3 4 1 1 AC INPUT socket Connect the AC power cord (supplied) securely to this socket and to a wall outlet. 2 Rear A terminals (AUDIO/VIDEO A terminals) When the monitor A selector button at the front of the monitor is pressed, the audio and video signals from the component which is connected to these terminals can be monitored. A AUDIO OUT/IN terminals B VIDEO OUT/IN terminals 3 Rear B terminals (AUDIO/VIDEO B terminals) When the monitor B selector button at the front of the monitor is pressed, the audio and video signals from the component which is connected to these terminals can be monitored. C AUDIO OUT/IN terminals D VIDEO OUT/IN terminals 4 Rear Y/C terminals (AUDIO/VIDEO Y/C terminals) When the monitor Y/C selector button at the front of the monitor is pressed, the audio and video signals from the component which is connected to these terminals can be monitored. E AUDIO OUT/IN terminals F S-VIDEO OUT/IN terminals Note: If there is no signal being input from the input terminals selected (A, B or Y/C) at the rear of the monitor, "NO SIGNAL" will be displayed. 5 CONNECTION Before making any connection, make sure all the devices are turned off. Before making the connections, please refer to the instruction manual accompanying each device. [. . . ] The cursor will move up or down, so that you can select the desired menu item. To return to the normal monitor screen · Press the OSD button once more, or · Select "EXIT: OSD" and then press the ENTER button. 7 ADJUST THE OSD MENU ITEM Open the menu screen (press the OSD button), use the cursor buttons to select the desired menu item, and then press the ENTER button. BRIGHTNESS adjustment 1 Select "3. 2 Use the cursor (l) and (j) buttons to adjust the brightness of the picture. OSD Note: The setting characters which are displayed on each adjustment screen (such as 50%) may not display correctly (dropout) in some cases. COLOR adjustment 1 Select "1. 2 Use the cursor (l) and (j) buttons to adjust the color of the picture. CONTRAST adjustment 1 Select "4. [. . . ]