User manual SANYO PDG-DXT10L

[. . . ] 2007 · · · · · · DLP is a registered trademark of Texas Instruments. IBM is a trademark or registered trademark of International Business Machines Corporation. Macintosh, Mac OS X and PowerBook are trademarks of Apple, Inc. , registered in the U. S. Windows, Windows 98, Windows Me, Windows XP or Windows 2000 are trademarks or registered trademarks of Microsoft Corporation. [. . . ] The following illustration shows the corresponding buttons on the remote control and on the projector. 1. To open the OSD, press the Menu button on the OSD control panel or remote control. Press the cursor or buttons to move through the initial menus and Select to enter the desired menu. 55 5. Using On-Screen Display 2. Press the cursor or button to move through secondary menus. 3. Press or to select menu items and or to change values for settings. Press Select to confirm the new setting. 4. Press Cancel to close the OSD or leave a submenu. 56 5. Using On-Screen Display Menu Tree The gray shaded areas indicate factory default settings. MENU Input ITEM Computer 1, Computer 2, Computer 3, Component, Video, S-Video CrossHatch, Raster(0%), Raster(25%), Raster(50%), Raster(100%), Raster Red, Raster Test pattern Green, Raster Blue, Raster Blue 60, Gray Raster 10, Gray Raster 30, Ramp H, Ramp V Image select High-bright/Presentation/Video/Movie/Graphic/sRGB Detail setting Basic Reference Gamma Color temp. Brilliant color White balance Red Green Blue Contrast R Contrast G Contrast B Color correction Contrast Brightness Sharpness Color Tint Reset Image options Screen Overscan PC Adj. Horizontal Vertical Total dots Fine sync Noise reduction 3D Y/C separation Progressive Color matrix Motion adaptive mode Volume Setting Basic Film 0~61 Keystone Lamp control Lamp mode Lamp Interval Simple menu Language 0 to 100 0 to 100 0 to 31 0 to 100 0 to 100 4:3/16:9/Side cut/True/Normal 0%/5%/10%/15% ±50 ±25 ±50 0 to 63 Off/Low/Mid/High Off/On Off/Still/Normal/Movie Auto/RGB/SDTV/HDTV Motion adaptor/Field Jam/Scaled Field/Mixed Mode Off/2-2/2-3 Auto/2-2 On/2-3 On Horizontal Vertical Normal/Eco Dual/Lamp1/Lamp2 Off/1 week/4 week/2000H On/Off English/Deutsch/Français/Italiano/Español/Svenska// Red, Green, Blue, Yellow, Magenta, Cyan High-Bright/Presentation/ Video/Movie/Graphic/sRGB Dynamic/Natural/Black detail 5000K/6500K/7800K/ 8500K/9300K/10500K 1 to 3 1 to 100 1 to 100 1 to 100 1 to 100 1 to 100 1 to 100 ­60 to 60 Adjust Image Video 57 5. Using On-Screen Display MENU Installation ITEM Ceiling & Rear Communication speed Menu color select Display time Background PIN code lock Key lock Dynamic black RC sensor Network setting Desktop Front/Ceiling Rear/Desktop Rear/Ceiling Front 4800bps/9600bps/19200bps/38400bps Color/Monochrome Manual/Auto 5sec/Auto 15sec/Auto 45sec Blue/Black/Logo Off/On Off/On Off/On Both, Front, Back DHCP Enable/Disable IP address Subnet Gateway DNS Network PIN code (0000 to 9999) Apply settings Normal/Power-saving PC control/Network Off/On Off/00:05/00:10/00:20/00:30 Off/On Normal/Max Last/Auto/Computer1/Computer2/Computer3/ Component/Video/S-Video Option Standby mode PC control On start Power management Screen trigger Fan control Default input select Information Usage time Input Network Version Reset Color system Video Auto/NTSC/PAL/SECAM S-Video Auto/NTSC/PAL/SECAM Remote control Code1/Code2/Code3/Code4/Code5/Code6/Code7/Code8 Message Off/On Filter warning Off/100[H]/200[H]/500[H]/1000[H] Search mode Normal/Fine Lamp1 life remaining, Lamp2 life remaining Lamp1 time, Lamp2 time PJ time Filter time Input name Signal H-sync freq. Video type Sync type Sync polarity Scan type IP address, Subnet, Gateway, MAC address Model name, Serial number, Firmware, Data, Remote control Current signal, All data, Clear lamp1 time, Clear lamp2 time, Clear filter time 58 5. Using On-Screen Display Menu Elements Some menus and windows contain large amounts of information in a small area. Refer to the following guide to navigate through options more easily. Menu windows or dialog windows typically contain the following elements: LABEL 1 2 3 4 5 6 7 8 Title ITEM Indicates the menu title. Highlight Menu type Radio button Slide bar Exit OK Cancel DESCRIPTION Click this round button to select an option in a dialog box. Using On-Screen Display Source Menu Descriptions and Functions The Source menu displays all supported image sources. Select the required source from the menu using or and press Select to confirm. ITEM Computer 1 Computer 2 Computer 3 Component Video S-Video DESCRIPTION Select the source connected to the Computer 1 input (see Connecting Your PC or Macintosh Computer on page 26). Select the source connected to the Computer 2 input (see Connecting Your PC or Macintosh Computer on page 26). Select the source connected to the Computer 3 input (see Connecting Your PC or Macintosh Computer on page 26). Select the source connected to the Component input (see Connecting Your DVD Player with Component Output on page 29). Select the source connected to the Video input (see Connecting Your VCR or Laser Disc Player on page 30). Select the source connected to the S-Video input (see Connecting Your VCR or Laser Disc Player on page 30). Displays information about the type of test pattern (Range: CrossHatch, Raster (0%), Raster (25%), Raster (50%), Raster (100%), Raster Red, Raster Green, Raster Blue, Raster Blue 60, Gray Raster 10, Gray Raster 30, Ramp H, Ramp V). Test Pattern 60 5. Using On-Screen Display Adjust Menu Descriptions and Functions The Adjust menu contains overall projector settings for image output such as sharpness, overscan and color matrix. Three tabs are accessible through the Adjust menu, Picture, Image Options and Video. Image menu The image menu is used to alter picture settings and can be accessed from the Adjust menu. The following table lists all functions with a description and the default setting. ITEM Image select Detail Setting Contrast Brightness Sharpness Color Tint Reset DESCRIPTION Select a set of preset values using or from the list. Notice that the below values will change depending on the preset selection. [. . . ] Frequency of Occurrence Power No power (POWER indicator does not light green) See also "Status Indicator (WARNING)". Power Management is turned off. always sometimes (How often?________) other (________) Video and Audio No image is displayed from your PC or video equipment to the projector. Still no image even though you connect the projector to the PC first, then start the PC. A combination of function keys will enable/disable the external display. [. . . ]