User manual SANYO PDG-DXL100

[. . . ] Multimedia Projector MODEL PDG-DXL100 Owner's Manual Table of Contents Table of Contents Usage Notice Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Introduction Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] to increase the sharpness. White Peaking Use the white peaking control to set the white peaking level of - towards the minimum setting. Color Temp. Gamma This allows you to choose a gamma bring out the best image quality for the input. 24 English User Controls Screen Adjust image distortion caused by tilting projector. Press the Press the to move the image left. to move the image right. Press the Press the to move the image down. to move the image up. Aspect Ratio Use this function to choose your desired aspect ratio. This format is for input sources not enhanced for Wide- Native This format displays the original image without any scaling. English English 25 User Controls Front-Desktop The factory default setting. Rear-Ceiling hind a translucent screen with ceiling mounted projection. 26 English User Controls Setting Input Search When this function is turned "On other signals if the current input signal is lost. When this function is turned "Off Fan Control Choose "On" to turn on Fan Control mode. Operate the fan at full speed continuously to allow for proper high altitude cooling of the projector. Lamp Life Reminder Choose this function to show or to hide the lamp end of life warning message. Choose "On" to dim the projector lamp which will lower power consumption and extend the lamp life. Choose "Off" to return to normal mode. BrilliantColor RS232: Allow RS232 control of an individual projector. Network: Allow network LAN via web browser (Internet Explorer) to control of projector. English English 27 User Controls N ot e Please turn this functo turn on "Power" by network during standby mode. Eco Standby Power (<1W) This function is available when the projector is turned off and in Stand-by. Off: normal power consumption in Stand-by condition. Remote Control This projector provides two different remote control codes: the factory-set initial code (Code 1) and the secondary code (Code 2). This switching function prevents remote control interference when operating several projectors or video equipment at the same time. To change the code for the projector: To change the code for the remote control: N ot e After keystone need to re-adjust screen again during display the closed caption. remote control operates properly. Closed Caption This function is a printed version of the program sound or other information displayed on the screen. If the input signal contains Use the or Sound Choose "On" to mute the volume. Choose "Off" to restore the volume. 28 English User Controls Press the Press the to decrease the volume. to increase the volume. Lamp Counter Reset Reset the lamp life hour after replacing a new lamp. Security Settings Security Settings: the projector. Off: Choose "Off" to be able to switch on the projector without Change Password: First Time: 1. Use number buttons on the remote to enter your new pass- N ot e Password default time). If you input incorrect projector will automatically shut itself down and enter into standby mode. Change Password: 1. Use number buttons to enter current password and then press - Factory Default Return the adjustments and settings to the factory default values. English English 29 User Controls Setting/Network Network Status Display the network connection status. Display the network connection status. Off: Assign an IP address manually. IP Address Select an IP address. Select subnet mask number. Gateway Select the default gateway of the network connected to the projector. DNS Select DNS number. Apply Press "ENTER" button to apply the selection. 30 English User Controls Language Language N ot e of powering on the menu is displayed to select the default language. All subsequent operations assume the selected default language. Choose the multilingual OSD. Press into the sub menu and then use the or or or key to select your preferred Information Information To display the projector information on the screen. English English 31 User Controls Controlling the Projector From Web dialogue box. 2. [. . . ] Composite sync and sync on green are not supported. 31. 35 50 English Appendices Computer Compatibility (DigitalHDMI) (1) PC digital signals with HDMI-DVI cable Modes Resolution V. Frequency (Hz) H. Frequency (kHz) 31. 50 31. 50 35. 20 XGA SXGA WXGA 55. 935 UXGA 31. 35 English English 51 Appendices (2) AV digital signals with HDMI cable Modes Resolution V. Frequency (Hz) 50 50 50 50 50 52 English Appendices Terminal : Analog RGB (Mini D-sub 15 pin) 5 10 15 14 4 9 13 3 8 12 2 7 11 1 6 1 2 3 *** 5 Ground (Red) Ground (Green) Ground (Blue) 9 10 11 12 13 sync. Input) ICP download 15 Terminal : Mini DIN 8-pin 8 5 2 7 4 1 6 3 1 2 3 5 RXD *** *** GND *** TXD *** *** English English 53 Appendices Regulation & Safety Notices This appendix lists the general notices of your Projector. FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this device does cause harmful to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. [. . . ]