User manual SANYO PDG-DWL100

[. . . ] Multimedia Projector MODEL PDG-DWL100 Owner's Manual Table of Contents Table of Contents Usage Notice Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Introduction Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It is recommended to use Eco under normal condition. On: lower power consumption than Normal mode in Stand-by condition. Off: normal power consumption in Stand-by condition. Remote Control This projector provides two different remote control codes: the factory-set initial code (Code 1) and the secondary code (Code 2). This switching function prevents remote control interference when operating several projectors or video equipment at the same time. When operating the projector in "Code 2", both the projector and the remote control must be switched to "Code 2". To change the code for the projector: Select either "Code 1" or "Code 2" in this Setting Menu. To change the code for the remote control: Press and hold both the MENU and IMAGE buttons together for 10 seconds or more. After changing the code, make sure the remote control operates properly. N ot e After keystone adjustment, maybe need to re-adjust screen again during display the closed caption. Closed Caption This function is a printed version of the program sound or other information displayed on the screen. If the input signal contains closed captions, you can turn on the feature and switch the channels. Use the or to select Off, CC1, CC2. Power Management Set the interval of power-off of the system, if there is no signal input. (minutes/unit) Sound Mute: Choose "On" to mute the volume. Choose "Off" to restore the volume. 28 English User Controls Volume: Press the Press the to decrease the volume. to increase the volume. Lamp Counter Reset Reset the lamp life hour after replacing a new lamp. Security Settings Security Settings: On: Choose "On" to enable security verification when turning on the projector. Off: Choose "Off" to be able to switch on the projector without password verification. Change Password: First Time: 1. Use number buttons to enter default password and then press "ENTER" to confirm. Use number buttons on the remote to enter your new password and then press "ENTER" to confirm. (The password has to be 4 digits. ) N ot e Password default value is "1234" (first time). If you input incorrect password 3 times, the projector will automatically shut itself down and enter into standby mode. 4. Use number buttons to enter current password and then press "ENTER" to confirm. Enter new password (4 digits in length) using the number buttons on the remote, then press "ENTER" to confirm. Enter new password again and press "ENTER" to confirm. Factory Default Return the adjustments and settings to the factory default values. (except for lamp counter and security setting) English English 29 User Controls Setting/Network Network Status Display the network connection status. DHCP Display the network connection status. On: Assign an IP address to the projector from the DHCP server automatically. Off: Assign an IP address manually. IP Address Select an IP address. Subnet Mask Select subnet mask number. Gateway Select the default gateway of the network connected to the projector. DNS Select DNS number. Apply Press "ENTER" button to apply the selection. 30 English User Controls Language Language N ot e In the first instance of powering on the projector, the language menu is displayed to select the default language. [. . . ] Please, dispose of them correctly at your local community waste collection/recycling centre. Please, help us to conserve the environment we live in! English English 55 Appendices Serial Control Interface This projector provides a function to control and monitor the projector's operations by using the RS-232C serial port. 1. Connect a RS-232C serial cross cable to SERVICE PORT on the projector and serial port on the PC. Launch a communication software provided with PC and setup the communication condition as follows: 3. [. . . ]