User manual SANYO PDG-DET100 CABINET DRAWING

[. . . ] 10 IMAGE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 D. ZOOM + Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 D. ZOOM ­ Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 POINTER RIGHT Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Example of Functional Execution Command: "C05" [CR] Example of Status Read Command: "CR0" [CR] 0û It clears the information of buffer in the following cases. (Until receiving the carriage return after the reception of the first data. ) 0û When pipelining control commands, allow interval time as below after the reception of response, . 1) [ZOOM UP/DOWN] [FOCUS UP/DOWN] [LENS SHIF UP/DOWN/LEFT/ RIGHT] commands. . . 100ms 2) Other commands. . . 500ms 0û 0û When pipelining Status Read command, allow at least 500ms of interval time after the response. Do not issue any command before receiving the response except the case that there is no response for 5 seconds. 0û It takes about 7 seconds for internal initialization after plugging in AC. 0û For 7 seconds after starting POWER ON in the status of STANDBY, the projector returns "Acceptable" response, but it does not carry out the command. carried out in 500 ms after the "Acceptable" response is returned. 0û About the behavior during Count Down and Cooling Down operation; in the period of the Count Down operation after Power ON or Cooling Down after Power OFF, "Acceptable" response is returned, but the command is not carried out except for Status Read command. 0û About the behavior during switching inputs; it takes 5 seconds to switch inputs after receiving the command. During this period, even if another command is received, it is not carried out although returning "Acceptable" response. However, Status Read commands are carried out in 500 ms after the "Acceptable" response is returned. This command works the same way as "" button of the projector and remote control. Acceptable Unacceptable [ACK] [CR] "?" [CR] Response 6. 25 ENTER Command COMMAND Detail Response "C3F" [CR] This command works the same way as "SELECT" button of the projector and remote control. Acceptable Unacceptable [ACK] [CR] "?" [CR] 11/23 PDG-DET100 Basic Serial Command Functional Specifications 6. 26 FREEZE ON Command COMMAND Detail "C43" [CR] Freeze on-screen picture This command works the same way as "FREEZE" button of the remote control, but it works only for turning on, not for turning off Freeze. Acceptable Unacceptable [ACK] [CR] "?" [CR] Response 6. 27 FREEZE OFF Command COMMAND Detail "C44" [CR] Cancel Freeze function This command works the same way as "FREEZE" button of the remote control, but it works only for turning off, not for turning on Freeze. Acceptable Unacceptable [ACK] [CR] "?" [CR] Response 6. 28 ZOOM + Command COMMAND Detail "C47" [CR] Make screen image larger This command works the same way as "ZOOM" button of the projector and remote control. Acceptable Unacceptable [ACK] [CR] "?" [CR] Response 6. 29 ZOOM ­ COMMAND COMMAND Detail "C46" [CR] Make screen image smaller This command works the same as "ZOOM " button of the projector and remote control. Acceptable Unacceptable [ACK] [CR] "?" [CR] Response 6. 30 FOCUS + Command COMMAND "C4B" [CR] Adjust focus of screen image (sharp and clear) with a long-focal-length ("=) (The lens direction is backward) This command works the same way as "FOCUS " button of the projector and remote control. Acceptable Unacceptable [ACK] [CR] "?" [CR] Detail Response 12/23 PDG-DET100 Basic Serial Command Functional Specifications 6. 31 FOCUS ­ Command COMMAND "C4A" [CR] Adjust focus of screen image (sharp and clear) with a short-focal-length (The lens direction is forward) This command works the same way as "FOCUS " button of the projector and remote control. Acceptable Unacceptable [ACK] [CR] "?" [CR] Detail Response 6. 32 LENS SHIFT UP Command COMMAND Detail Response "C5D" [CR] Move screen image upward Acceptable Unacceptable [ACK] [CR] "?" [CR] 6. 33 LENS SHIFT DOWN Command COMMAND Detail Response "C5E" [CR] Move screen image downward Acceptable Unacceptable [ACK] [CR] "?" [CR] 6. 34 LENS SHIFT LEFT Command COMMAND Detail Response "C5F" [CR] Move screen image to the left. Acceptable Unacceptable [ACK] [CR] "?" [CR] 6. 35 LENS SHIFT RIGHT Command COMMAND Detail Response "C60" [CR] Move screen image to the right. Acceptable Unacceptable [ACK] [CR] "?" [CR] 6. 36 AUTO PC ADJ. [. . . ] The status is kept until the next operation starts. 0û "88" [CR] Status: Standby after Cooling Down due to Abnormal Temperature This value is returned when Cooling Down operation due to Abnormal Temperature has been completed and the status has been moved to Standby. The status is kept until the next operation starts. 0û "2C" [CR] Status: Cooling Down in process due to Shutter management function This indicates it has moved to Cooling down status according to the setting of Shutter Management function in setting menu. During this time, Functional Execution Commands are not accepted. 0û "88" [CR] Status: Standby after Cooling Down due to Shutter management function This value is returned when Cooling Down operation due to Shutter management has been completed and the status has been moved to Standby. When projector is turned on again, it cancels the last status and starts normal operation. 18/23 PDG-DET100 Basic Serial Command Functional Specifications 7. 4 Input Mode Read Command COMMAND Detail "CR1" [CR] Get currently selected SLOT Acceptable "%1" [CR] "1" = Input 1 is selected "2" = Input 2 is selected "3" = Input 3 is selected "4" = Input 4 is selected (In the case SLOT method, SLOT 1~4 is selected. ) "?" [CR] Response %1 Unacceptable 7. 5 Lamp Time Read Command COMMAND Detail "CR3" [CR] Get total lamp running hours Acceptable "%1_%2" [CR] Each lamp data follows in sequence with one space between each of them. [. . . ]