User manual SANYO HT27745

[. . . ] If the problem still persists, contact the dealer where you purchased the projector or the service center. Safety Precaution WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Be especially careful that children do not stare directly into the beam. ­ Provide appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. [. . . ] Move a red arrow pointer to any of Mode 1 to 5 that you want to store and then press SELECT button. Mode free To clear adjustment parameters previously set, move a red frame pointer to Mode free icon and then press SELECT button. Move a red arrow pointer to Mode that you want to clear and then press SELECT button. Reset Reset all adjust parameters on adjustment dialog box to previous figure. To clear adjustment data. Vacant Mode Shows values of "Total dots, " "Horizontal, " "Vertical, " "Display area H, " and "Display area V. " Store icon Close this dialog box. Mode free icon 30 COMPUTER INPUT PICTURE IMAGE ADJUSTMENT IMAGE LEVEL SELECT (DIRECT) Select image level among Standard, Real, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE/IMAGE SEL. IMAGE button Standard Real Image 1 Image 2 Image 3 Image 4 IMAGE LEVEL SELECT (MENU) 1 2 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to IMAGE SELECT Menu icon. Press POINT DOWN button to move a red frame pointer to level that you want to set and then press SELECT button. Standard IMAGE SELECT MENU IMAGE SELECT Menu icon Normal picture level preset on this projector. IMAGE 1~4 User preset picture adjustment in IMAGE ADJUST Menu (P32). Level being selected. Wide Provides image to fit wide video aspect ratio (16 : 9) by expanding image width uniformly. This function can be used for providing a squeezed video signal at 16 : 9. Digital Zoom + When Digital Zoom + is selected, ON-SCREEN MENU disappears and message "D. Digital Zoom ­ When Digital Zoom ­ is selected, ON-SCREEN MENU disappears and message "D. To cancel Digital Zoom +/­ mode, press any button except SELECT, POINT UP/DOWN/LEFT/RIGHT and AUTO PC ADJ. buttons. NOTE Picture screen adjustment cannot be operated when "720p (HDTV)", "1035i (HDTV)", "1080i/50 (HDTV)" or "1080i/60 (HDTV)" is selected on PC SYSTEM Menu (P27). True and Digital Zoom +/­ cannot be operated when "480i", "575i", "480p" or "575p" is selected on PC SYSTEM Menu (P27). This projector cannot display any resolution higher than 1600 X 1200. If your computer's screen resolution is higher than 1600 X 1200, reset resolution to lower before connecting projector. Image data in other than XGA (1024 x 768) is modified to fit screen size in initial mode. Panning function may not operate properly if computer system prepared on PC ADJUST Menu is used. 33 VIDEO INPUT SELECTING INPUT SOURCE DIRECT OPERATION Select INPUT source by pressing INPUT 1/2, INPUT 3/4 or INPUT 1 - INPUT 4 buttons on Side Control or on Remote Control Unit. INPUT 1/2 button INPUT 1 INPUT 2 INPUT 3/4 button INPUT 3 INPUT 4 MENU OPERATION 1 2 Press MENU button and ON-SCREEN MENU will appear. [. . . ] 4. ) After installing the lens, make sure the Lens is not loose and properly installed. E LENS LOCK RELEASE Grasp (unlock) Lens Lock Lever and pulling upward. LENS LOCK Grasp (unlock) Lens Lock Lever and fully pulled downward until it is locked (clicked). Fig-6 -3- Fig-7 6 This projector has 6 Light-Block Sheets. (Refer to the list below. ) Use 1 Light-block Sheet for MODEL LNS-W03 Set 2 Light-Block Sheets through the lens. Make sure the shape of the Light-Block Sheets are correct and be sure to set them as shown in the Fig. Make sure the mark (TOP and BACK) on Light-Block Sheets are correct and set them properly. Light-Block Sheets For each lens. Lens Model No. [. . . ]