User manual SANYO HEC-FX1

[. . . ] a pacemaker) Those who have a serious blood circulation disorder in the legs Never attempt to dismantle the chair. Do not allow any personnel other than a qualified repair technician to dismantle or repair the chair. Do not attempt to damage, break, modify, bend forcibly, pull, twist or bundle the cord. In addition, do not place heavy objects on the cord or jam the cord between objects. [. . . ] Otherwise, it may result in fire due to electric shock, current leakage, short circuit, etc. When the equipment will not be used for an extended period, be sure to disconnect the power plug from the outlet. Otherwise, it may result in electric shock, current leakage or fire due to damaged insulation. Otherwise, an accident may happen or damage to the machine may result. 3 4 NAME/FUNCTION OF EACH PART Control Pillow Head rest ON/OFF lamp Illuminates when the control is on. Seat Back rest ON/OFF button Used for switching the operation ON/OFF. (See page 9) (See page 11) Control Arm rest STOP button Used if you have felt abnormal physical sensation or want to stop the operation immediately. (See page 11) Foot rest Cord Power plug PROGRAM SELECTION button Used to select from two kinds of courses "STRETCH" and "RELAX". (See page 11) RELAX lamp STRETCH lamp Check the accessories at first. Head rest ZERO-G button Used to set the back rest, foot rest, and seat to prearranged reclining angles. (See page 9) HOME POSITION button Caster Installation screws (2 screws) Used when moving the chair. (See page 7) Used to return the back rest, foot rest and seat to home positions. (See page 10) Pillow POWER switch Used to turn on/off the power source. (See page 8) (See page 12) RECLINING button Adjusts the angle of the back rest, foot rest and seat. The back rest, foot rest and seat are moved in conjunction with each other. (See page 10) 5 6 HOW TO PLACE THE CHAIR How to move the chair HOW TO INSTALL THE HEAD REST AND PILLOW 1 Raise the back rest. Movement becomes easier when the back rest is raised. and move it using PUSH PULL 1 Remove the screws (x2) from the head rest. Head rest inserting the head 2 Afterthe pipe, secure therest into head rest firmly with the screws (x2). Head rest Pipe Hole Screws Back rest Caster Screws NOTE Before moving the chair, be sure to remove the power plug from the outlet. Be sure to move the chair with the assistance of another person on an easily damaged floor surface or concrete surface. Before moving the chair, make sure that the Åñ head rest is securely attached. (See page 8) Be Åñ careful when moving the chair by holding the head rest as doing so may cause the head rest to tilt forward. The chair can be carried by two persons with each holding the arm rests on the left and the right respectively. In this case, however, ensure that the control is not raised. fastener back 3 Unzip thecover the of therest pad, and back with the back pad. fastener 4 Zip up the fastener of the back pad. Back pad Back rest Foot rest Back pad fastener Back rest To move the chair, one person should hold the foot rest and the other should hold the back rest with the back rest reclined. the 5 Secure the head rest andand loop 6 Place the pillow on the head back pad with the hook rest. fasteners. Head rest Back pad Pillow Head rest Decide where to place it 1 Lay a carpet, etc. on the set-up place. It prevents damaging the floor, and muffles the noise during use. is sufficient space 2 Ensure therechair to recline. [. . . ] Disconnect the power plug from the outlet and consult the sales agent. Do not attempt to repair the equipment at home by yourself, as it is very dangerous. SPECIFICATIONS Power consumption Rated time Timer 110 W 30 min. 15 minutes 780 mm [width] Å~1, 030 mm [depth] Å~1, 230 mm [height] ÅñWhen not reclined (with foot rest retracted) 780 mm [width] Å~1, 740 mm [depth] Å~715 mm [height] ÅñWhen reclined (with foot rest set horizontally) Approx. 115 Å` 155Åã Back rest: Motor-driven type (Linked with foot rest and seat) Foot rest: Motor-driven type (Foot rest only) Approx. [. . . ]