User manual SANYO HEC-DR3000

[. . . ] Moreover, be careful not to operate the back rest with the cord hooked on some obstruction. Otherwise, unreasonable force may be applied to the cord, possibly resulting in fire or electric shock. Be sure to check that there is no-one (children in particular), or any pets under the foot rest prior to lowering the foot rest. Do not attempt to stand on the arm rest, foot rest, back rest, or remote control stand. [. . . ] When switched form ZERO-G 2 to 1, the back rest is raised first, and moves to the set angle. Reclining can be stopped during the reclining motion by pressing either the ZERO-G button, HOME POSITION button, RECLINING button, FOOT REST button, OPERATION ON/OFF button, or STOP button. When the reclining motion is stopped by pressing the STOP button, press the OPERATION ON/OFF button to resume the operation. When the reclining motion is stopped by pressing buttons other than the STOP button, press the desired button for motion. When back rest angle is adjusted from the ZERO-G 2, massaging other than Air Course can be selected. 2 Adjust the position of head cover. Adjust the attaching position with Head cover hook-and-loop fasteners. During the massage, adjust the head cover not to touch the shoulders. of 5 Adjust the anglefoot the back rest. The back rest and rest are moved Hook-andloop fasteners Keep the RECLINING button pressed until the desired angle is achieved. (Seat only cannot be adjusted. ) Raise the back rest, and lower the foot rest by continuously pressing the UP ( ) button. Foot rest may be raised Åñ depending on the angle. 120 ÅK Foot rest OR Adjustment range Approx. 50Åã 3 Press the OPERATION ON/OFF button. When the button is pressed, the lamp of the remote control illuminates and the sole warmer will turn on. When the foot rest is fully lowered, the foot rest will rise a little. The degree of stiffness cannot be measured if your fingers are not placed on the sensor. (The sensor lamp will flicker and the characters of "Grip the sensor" on the remote control will be illuminated. ) In such a case, massages will be carried out according to the standard operation of the selected course. When the user's skin is dry (especially a person with dry skin), the degree of stiffness may not be measured correctly. In such a case, slightly moisten the fingers using hand cream and place the fingers on the sensor again. Press Back rest 15 16 MASSAGING (WHOLE BODY SENSOR AUTOMATIC COURSE) 6 Starts massaging automatically. Measure the position of shoulder. Ö@ Check if the position of shoulder is correct. (See page18) Measurement of shoulder position Measure the position of shoulder and match the position of massaging rollers to that of shoulder. Massaging rollers move up and down to measure the position of shoulder. (Sit deeply on the massage chair and raise your head slightly. The matching of the position of shoulders may not be possible if the head is leaning on the back rest. ) Massaging operation and display of remote control Displays the aim of massaging positions, the type of massaging, the stiffness, body pressure and the remaining massaging time on the remote control. Explanation with an example of STIFFNESS SENSOR MASSAGE Measurement of the degree of stiffness. ÖA Start sensor massage. Measures the degree of stiffness in each part of body with the sensor and informs of the degree of stiffness. Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ (See page 18) Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ ÖB Massages according to the stiffness. Adjusts the operation and strength of standard massaging according to the measured degree of stiffness. Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ (See page 18) Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Å@ Massaging operation at recognized position of shoulder. The sensor will display the positions of stiffness (those where stiffness has been felt) by measuring the amount of perspiration from fingers and pulse in reaction to sensor massage. When measuring the degree of stiffness, the result is displayed by the ring around the REPEAT! [. . . ] Do Åñ not make contact with vinyl products for an extended period. It may cause discoloration. Back rest MAIN UNIT (Cloth part, plastic parts, and pipe) Soak a soft cloth in diluted neutral kitchen detergent, and squeeze it well. Wipe the main unit with the damp cloth, and wipe it with a dry cloth afterwards. REMOTE CONTROL, SENSOR CONTROLLER Wipe with a soft dry cloth. Do Åñ not wipe with a damp cloth. 25 26 CONTENTS OF MASSAGING Åq WHOLE BODY SENSOR AUTOMATIC COURSEÅr ÅñThe drawing of the massage for each course is omitted in part, in order to describe the operation in a simplified manner. [. . . ]