User manual SANYO FPW-EXA025 INSTALLATION AND SERVICE MANUAL

[. . . ] Multi-Deck Self Service Multi-Deck Self Service Fresh Meat Merchandiser Fresh Meat Merchandiser FPW-EXA085 FPW-EXA085 FPW-EXA025 FPW-EXA025 INSTALLATION AND SERVICE MANUAL REMOTE TYPE DISPLAY CASE TABLE OF CONTENTS 1 2 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 DIMENSIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. 1 2. 2 EXTERNAL DIMENSIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 FOOTPRINT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] APPARENT DAMAGE: Any obvious loss or damage should be noted immediately at the time of receipt on the freight bill or express receipt and signed by the carrier's agent. CONCEALED DAMAGE: If damage that is not apparent during unloading is found after unpacking, retain all packing materials and submit a written request to the carrier for inspection within 15 days. LOST ITEMS: Any claims related to lost or missing items must be made to SANYO Commercial Solutions Company within 48 hours of receipt of equipment. 3. 4 Unloading Instructions & Precautions WARNING Cases are heavy and bulky, and require at least two people for unloading, moving, and installation. Do not remove the wooden beam from the bottom front edge of each case until the cases have been moved into place in the store lineup. Walking on the top of the merchandiser may lead to serious injury and/or damage to the merchandiser. Use dollies on both ends of the merchandiser to move to lineup location after unloading from container. 6 3. 5 Aligning Cases WARNING Cases are heavy and bulky, and require at least two people for unloading, moving, and installation. Walking on the top of the merchandiser may lead to serious injury and/or damage to the merchandiser. Review layout drawings for spaces where merchandisers are to be installed. Based on the layout drawings and the merchandiser footprint drawings, mark the floor to indicate the exact locations of the base legs (back edge and front edge) on each merchandiser. Multiple merchandisers should be aligned based upon the position of the base legs. Snap chalk lines for the front and rear positions of the legs on each row of merchandisers. Mark the location showing the outside edge of each base leg on each merchandiser. 3. 4. 3. 6 Case Leveling Merchandisers must be installed level in order to ensure proper performance and drainage. For each lineup of cases to be joined, use a level (preferably a laser level) to find the highest point on the front and rear chalk lines marked in step 3 above (during Case Alignment). Estimate the number of shims needed for the four corners of each case position, in order to bring all positions to the same height as the highest point found in step 2. For each row, place the first merchandiser case where it will sit over the highest point in the lineup. Ensure that the case is level, using shims as needed. 2. 3. 4. NOTE: Each base leg should rest on solid supports. Insert shims as needed if there are any gaps between the floor and each base leg. Continue placing cases in the lineup, working outward to both sides from the position of the first case placed. Fix washers and nuts (item 3 in above drawing) to the ends of the M8 bolts inside the merchandiser in the two locations indicated. Cover the M8 bolt heads and insulation outside the patch end with patch end caps. Cover ends of M8 bolts inside the merchandiser with caps (item 6 in above drawing). Corner hole Apply silicone sealant NOTE: NSF requires that any bolt or screw in the product area be capped or cut off. [. . . ] Make sure to clean under mats or objects resting on the shelf surfaces. 6. 4 a. f. Shelf Assemblies (Weekly Cleaning) Start shelf assembly cleaning by turning all fluorescent lamps off. Remove all shelf guards and price tag molding (see Section 6. 2 above). Thoroughly check the underside of each shelf for drips or other foreign substances and clean. [. . . ]