User manual SANYO ECD-T1550

[. . . ] The two supplied keys release tabs inside the unit's sleeve so you can remove it. Insert the keys as far as they will go (with the notches facing up) into the appropriate slots at the middle left and right sides of the unit. Then slide the sleeve off the back of the unit. 3 INSTALLATION Sleeve L Key metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical grounding of the unit. Spring Washer Metal Strap Hex Nut R Key Mounting Bolt Plain Washer Tapping Screw 4. [. . . ] The adjustment mode will change in the following order: VOL (Volume) BAS (Bass) TRE (Treble) BAL (Balance) FAD (Fader) SET THE CLOCK Press the DSP button (15), the clock is shown on the LCD display. Then press the MANU/SKIP button (17) to change hours or MANU/SKIP button (16) to change minutes. If any button (except button (4)) is pressed in the mute state, the mute mode is released. EQUALIZATION Press EQ button (24) to turn on equalization function and to select desired audio mode. There are five kinds of mode as below: FLAT CLASSICS POP M ROCK M DSP OFF By pressing VOLUME + button (11) or VOLUME- button (27), it is possible to adjust the desired sound quality. BEEP ADJUSTMENT Press SEL button (10) and hold for more than 2 seconds until "BEEP" appears on display. Press VOLUME+ button (11) or VOLUME- button (27) as follows: BEEP 2ND BEEP ALL BEEP OFF LIQUID CRYSTAL DISPLAY Exhibit current frequency and activated functions on the display (8). AUXILIARY INPUT The unit can be connected to a portable audio player through the AUX IN jack (7). Note : The face plate will not close when something is plugged in the AUX in jack. REMOTE SENSOR Point the remote control handset to the remote sensor IR (23). RESET FUNCTION RESET button (12) can be activated with either a ballpoint pen or thin metal object. The RESET button is to be activated for the following reasons: - Initial installation of the unit when all wiring is completed. - Error symbol on the display. - BEEP 2ND mode: The beep is only generated when all allowed double function button is pressed long (several seconds). - BEEP OFF mode: The beep is disabled. 9 OPERATION RADIO OPERATION · SWITCHING TO RADIO MODE Press MOD button (6) shortly to select radio mode, the radio mode appears in the display together with the memory band and frequency. · SELECTING THE FREQUENCY BAND At radio mode, press BND/LOUD button (13) shortly to select the desired band. The reception band will change in the following order: FM1 FM2 FM3 AM · AUTOMATIC MEMORY STORING & PROGRAM SCANNING - Automatic Memory Storing Press AMS button (18) for several seconds, the radio searches from the current frequency and checks the signal strength until one cycle search is finished. The six strongest stations will be stored into the corresponding preset number button. - Program Scanning Press AMS button (18) shortly to scan preset station stored in memory. · STATION STORING Press any one of the preset buttons (14) (M1 to M6) to select a station which had been stored in the memory. Press this button for several seconds (until 2'nd beeps come out) to store current station in that preset button. [. . . ] LABOR 1 YEAR PARTS 1 YEAR EXCLUSIONS This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model's instruction manual, or (B) the repair of any product whose serial number has been altered, defaced or removed. This warranty does not apply to the cabinet or cosmetic parts, knobs or routine maintenance. This warranty does not apply to the elimination of car static or motor noise, correction of antenna problems, or damage to compact discs, speakers, accessories or vehicle electrical systems. This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear. [. . . ]