User manual SANYO EC505

[. . . ] Macintosh is a registered trademark of Apple, Inc. intheUSAandothercountries. PowerPCisaregisteredtrademarkofIBMCorporation. IntelCoreis a registered trademark of Intel Corporation in the USA and other countries. Each name of corporation or product in this owner's manual is either a registered trademark or a trademark of its respective corporation. ·TheOn-ScreenMenuandfiguresinthismanualmaydifferslightlyfromtheproduct. ·Thecontentsofthismanualaresubjecttochangewithoutnotice. 2 Memory card for the Memory Viewer function The memory card is not provided with this projector. [. . . ] The card comes out. Direct start-up into the memory viewer mode After inserting the SD memory card, the SD memory card indicator blinks, "Wired" or "Wireless" from the input menu of the projector is automatically selected, the memory viewer start-up image appears briefly and then an image stored in the SD memory card is displayed on the screen. *Automatically, the same input of "Wired" or "Wireless" is selected as last time. *If the image file is not available in the root directory of the SD memory card, the memory viewer browser window appears. *During operating the Network Viewer, the Network Capture or the Moderator functions, the direct start-up into the memory viewer mode can not operate. *When the projector is turned off and on while the SD memory card is left inside in the memory viewer mode, the projector starts into the memory viewer mode and an image stored in the SD memory card is displayed on the screen. When you press CANCEL button in the memory viewer mode, the memory viewer browser window as shown on page 6 appears on the screen. When you remove the SD memory card during operating the projector in the memory viewer mode, the input source returns to the previous one selected just before inserting the SD memory card. Note: During accessing to the SD memory card, do not turn off the power or eject the card because the data in the card might get damaged. During accessing, the SD memory card indicator is blinking The SD memory card allows you to insert or remove regardless of the power status of the projector. The direct start-up into the memory viewer mode may not operate when the SD memory card is inserted immediately after being removed. The Network Viewer and the Moderator functions are non-Mac-compliant. 4 Entering the memory viewer mode In case of already SD memory card is inserted into the card slot on the side terminal of the projector and you want to enter the memory viewer mode again: 1. elect"Wired"or"Wireless"fromtheinputmenuoftheprojector. The dialogue window appears S and select "Yes" and press SELECT button to start the auto display. The display period of the image and the number of repeat are set with the program file. During displaying the image, you can control the displayed image with control buttons as described in the table below. Point Operation d e 8 7 Manual playback with next file Manual playback with previous file Start auto-playback Stop auto-playback Termination of memory viewer To terminate the memory viewer function, take one of methods described below. - Terminate with projector's on-screen menu. 1. Select"Wired"or"Wireless"fromtheinputmenuoftheprojector. PressSELECT button. 2. Select"MemoryViewer"withthepointed buttons and press SELECTbutton. The"Enter/Exit"pallet of the memory viewer appears. 3. Select"Exit"andpresstheSELECT button. - Terminate with memory viewer mode 1. 3. Select"Exit"onthebrowserwindowwiththepoint7 8 buttons and press SELECT button. While operating the memory viewer, the Network Viewer and Network Capture function cannot be used. Notes for Windows: * The program file (. dpf ) is created with the program editor software. For further information, see the item"Creatingaprogramfile[ProgramEditor]"(p. 115)describedontheseparatednetworkowner's manual. * The DispParam folder is automatically created when the program file with the program editor is stored. [. . . ] aunchtheexplorersoftwareofthecomputerandtypetheIPaddressoftheprojectorwhichhasthe L SDmemorycardontotheaddresscolumn. Forexample, "ftp://192. 168. 1. 201". The contents of the SD memory card appear on the explorer window as below. 2. MovetheprojectiondatafromthecomputerintotheSDmemorycard. Note: If the network PIN code is set for the projector, the authentication window appears as below. In that case, enter "user" into the User Name column and the network PIN code of the projector into the Password column. [. . . ]