User manual SANYO EC232

[. . . ] Operating the projector properly enables you to manage those features and maintains it in better condition for many years to come. Improper operation may result in not only shortening the product life, but also malfunctions, fire hazard, or other accidents. Safety Precaution ­ ­ ­ This apparatus must be earthed. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Do not stare directly into the lens, otherwise eye damage could result. [. . . ] If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation. When the projector exhibits a distinct change in performance-this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons. Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition. 3 English Hot air is exhausted from the exhaust vent. When using or installing the projector, the following precautions should be taken. ­ Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes. ­ Keep the exhaust vent at least 3' (1 m) away from any objects. ­ Do not touch a peripheral part of the exhaust vent, especially screws and metallic part. Objects put on the cabinet will not only get damaged but also cause fire hazard by heat. MENU Press "MENU" to launch the Onscreen display (OSD), back to the top level of OSD for the OSD main menu operation IMAGE Select the Image mode from Presentation, Movie, sRGB, Bright and User. 8 7 N ot e To quick change remote control code, press "MENU" and "IMAGE" buttons about 10 seconds at the same time. 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 N ot e The bottom side of OSD menu might be out of display when user adjusts keystone value, under the status of low resolution signal input and different aspect ratio setting. To solve this problem, please adjust keystone value in "Aspect Ratio" of "4:3" then switch back to your desired aspect ratio. Press "INPUT" to choose RGB, SCART, Component, S-Video, Composite and HDMI sources. KEYSTONE +/- Adjust the image to compensate for distortion caused by tilting the projector. Point the remote Maximum operating range control from obliquely for the remote control is above toward the Inabout 39. 4' (12m) and 60° in frared Remote Receiver top of the projector. when operating the remote control. 39. 4' (12m) Approx. 30° 10 Connecting the Projector Connect to Computer/Notebook VGA, DVI N ot e Make sure that the power plug is fully inserted into both the projector AC inlet and the wall outlet. The AC outlet must be near this equipment and must be easily accessible. Audio Output 2 3 4 5 6 SERVICE PORT S-VIDEO IN VIDEO IN MONITOR OUT COMPUTER IN 1 COMPONENT IN 1 AUDIO IN (VARIABLE) AUDIO OUT COMPUTER IN 2 COMPONENT IN 2 E62405SP R N ot e Due to the difference in applications for each country, some regions may have different accessories. 1 8 7 Monitor Output When AUDIO OUTPUT is plugged-in, 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power cable (supplied) the projector's build-in 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RS232 cable speaker is not available. 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HDMI-DVI cable 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGA cable (supplied) 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio in cable jack to jack 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio out cable jack to jack 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Network cable 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Monitor out cable ensure the projector works well with your computer, To please make sure the timing of the display mode is compatible with your projector. 11 English N ot e Make sure that the power plug is fully inserted into both the projector AC inlet and the wall outlet. [. . . ] If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, simply press "ON/STAND-BY" to restart the projector. Disconnect the power cable from the electrical outlet and the projector. Do not turn on the projector immediately following a power off procedure. 16 On Screen Display The Projector has a multilingual On Screen Display that allows you to make image adjustments and change a variety of settings. [. . . ]