User manual SANYO DSR-M814

[. . . ] e00_VDH_M814. book Page A Thursday, October 28, 2004 9:59 AM e00_VDH_M814. book Page 1 Thursday, October 28, 2004 9:59 AM PRECAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Declaration of Conformity Model Number Trade Name Responsible party Address : DSR-M814 : SANYO : SANYO FISHER COMPANY : 21605 Plummer Street, Chatsworth, California 91311 Telephone No. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. CAUTION: Changes or modifications not expressly approved by the manufacturer may void the user's authority to operate this equipment. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] The digital video recorder can automatically detect whether the copy destination is a CompactFlash card or a CD-R/RW disc. ( P. 55) Copying to external media Connect either a CompactFlash card reader or a CD-R/RW drive to the USB port on the front of the digital video recorder. 27 e00_VDH_M814. book Page 28 Thursday, October 28, 2004 9:59 AM COPYING RECORDED VIDEOS TO EXTERNAL MEDIA 2 Press the [ ] and [ ] buttons to select "COPY SET" and press the [ ] button. The <COPY SET> screen appears. (1) (3) (5) (6) (7) 4 Press the [ ] and [ ] buttons to select "COPY START", and then press the [ ] button. Copying of video starts. (2) (4) (1) RECORDING TOP: Displays the date and time of the video recorded first. (2) RECORDING END: Displays the date and time of the video recorded last. (3) COPY SIZE: Displays the amount of data between "START TIME" and "END TIME" in MB. If this data is less than 1 MB in size, "-----" is displayed and "COPY START" will not be possible. A date and time earlier than "START TIME" cannot be specified. (7) Preview: Displays the image corresponding to the date and time set by "START TIME" or "END TIME". OPERATION When copying has been completed, "COPY FINISHED" appears, and the screen will return to the live video display when any button is pressed. Example: Copying from 10:15 on April 25th with a DVR NAME of "FRONT" CompactFlash card, CD-R/RW FRONT (1) 0425-1015. mp2 0425-1015-1. mp2 0425-1015-2. mp2 (2) 3 Press the [ ] and [ ] buttons to specify "START TIME" and "END TIME", and then press the [ ] button. (1) A folder is created for the DVR NAME on the CompactFlash card, or CD-R/RW. (2) A file is created inside that folder with its name reflecting the date and time. If "DVR NAME" has not been set, the name "DSR-M814" will be used when creating folders. The character "+" will be used to replace any slash (/), semi-colon (;), asterisk (*), period (. ), or colon (:) characters appearing in "DVR NAME". When adding data to the same CompactFlash card, folders such as "Folder name-1" will be created. For information on CompactFlash readers and CD-R/RW drives that can be connected, contact the dealer or Sanyo service center. 28 e00_VDH_M814. book Page 29 Thursday, October 28, 2004 9:59 AM COPYING RECORDED VIDEOS TO EXTERNAL MEDIA Formatting a CompactFlash card or CD-RW 1 Press the [SEARCH] button while the digital video recorder is recording or stopped. The <SEARCH/COPY> screen appears. 29 OPERATION 2 Press the [ ] and [ ] buttons to select "FORMAT MEDIA" and press the [ ] button. The <WARNING> screen appears. "NO" flashes. 3 Press the [ ] and [ ] buttons to select "YES" and press the [ ] button. Formatting of the media starts. When formatting has been completed, "FORMAT FINISHED" appears, and press the [ ] button to return to the <SEARCH/COPY> screen. e00_VDH_M814. book Page 30 Thursday, October 28, 2004 9:59 AM SETTINGS 1. MENU CONFIGURATION This section describes the menu configuration, and which menu item to select for each operation. To change the settings Use the [ ], [ ], [ ] and [ ] buttons to change the settings in each setting screen. Operating menu screens [ ] button [ ] button [ ] button [MENU] button (2) (3) (1) [ ] button [EXIT/OSD] button (1) To move the cursor up or down Press the [ ] or [ ] button. (2) To move the cursor right or to a setting item Press the [ ] or [ ] button. (3) To change a setting value Press the [ ] or [ ] button. SETTINGS 1 Press the [MENU] button. The <MAIN MENU> screen is displayed. 4 2 Press the [ ] or [ the desired item. ] button to select When you are finished changing the settings, press the [EXIT/OSD] button to end. The display returns to the normal screen. You can display the menu screen during recording, but not during playback. Press the [ ] button to return to the menu screen from the sub-menu screen. (Example: Selecting "5. [. . . ] "NO" flashes. (continued) 64 e00_VDH_M814. book Page 65 Thursday, October 28, 2004 9:59 AM MENU UPLOAD/DOWNLOAD 2 Press the [ ] or [ ] button to select "YES", then press the [ ] button. CompactFlash card formatting starts. When formatting has finished, the display returns to the <MENU UPLOAD/DOWNLOAD> screen. Formatting a CompactFlash card erases all the data stored on it. To cancel formatting, select "NO". To exit Press the [EXIT/OSD] button. The display returns to the normal screen. SETTINGS 65 e00_VDH_M814. book Page 66 Thursday, October 28, 2004 9:59 AM APPENDIX 1. CONTROL TERMINAL SPECIFICATIONS Connecting cables to the control terminals Cable 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Terminal No. Name RS-485A RS-485B C REMOTE C Signal RS-485 RS-485 Function To RS-485 terminal signal A*1 To RS-485 terminal signal B*1 Common 1 2 3 4 5 6 Flat-blade screwdriver (1) Push in the lock pin with a flat-blade screwdriver. The cable is now secured in place. Resistance ladder connection Remote Control terminal Common Input for clock setting Normal open, CLOCK ADJ IN Low level active CLOCK ADJ OUT C SERIES REC IN Normal open, Low level active Normal resistance 5V DC/57k, Low level active System controller connections The connections for a system controller are shown below. [. . . ]