User manual SANYO DSR-300

[. . . ] PRECAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Declaration of Conformity : DSR-300 : SANYO : SANYO FISHER COMPANY : 21605 Plummer Street, Chatsworth, California 91311 Telephone No. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Model Number Trade Name Responsible party Address CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. [. . . ] Always performs alarm recording, regardless of whether or not timer recording is being performed. Performs alarm recording only during timer recording. 10- 20- 04 ALARM 0000 08: 30: 00 EN 10FPS AL-REC ON TIMER AL-REC OFF Performs alarm recording only when timer TIMER recording is not being performed. Performs alarm recording only for the amount * DLY AL-REC of time set by the timer. Normal recording is ON TMR not performed. If a new alarm occurs during alarm recording Recording switches from the previous alarm image to the new alarm image in a seamless process. If a number of different alarms occur, these are treated as a single alarm until an alarm interruption occurs. * "DLY AL-REC ON TMR" is enabled just by making timer settings. There is no need to press the [TIMER] button. 8 Move the cursor to "REC RATE" and "DURATION" and press the [ ] button, then press the [ ] or [ ] button to change the setting. The maximum number of images (shown in parentheses) changes in accordance with the new settings. Maximum number of images Settings cannot be made for "PRE-ALARM RECORDING" when "ALARM RECORDING" is set to "OFF". The alarm history (recording list) displays up to the last 9, 999 items. (Although the history can record up to 16, 000 items, only 9, 999 of these can be displayed onscreen. ) When the normal recording area is set to "*1%", alarm recording is performed for as long as space is left in the alarm recording area. For "1%" and other settings, up to 16, 000 items are recorded per hard disk. English 65 8 ALARM REC MODE SET Setting pre-alarm recording When settings have been completed 1 Move the cursor to "PRE-ALARM RECORDING" and press the [ ] button, then press the [ ] or [ ] button to change the setting. Press the [EXIT/OSD] button. The display returns to the normal screen. Number of alarm recordings PRE display 10-20-04 PRE 0023 08: 30: 00 EN 10FPS [Settings] ( Setting OFF ON indicates default setting. ) Description Pre-alarm recording is not carried out Pre-alarm recording is carried out Setting the alarm trigger This setting indicates how intruders are to be detected. SETTINGS <MAIN MENU 1> 2 Move the cursor to "REC RATE" and "DURATION" and press the [ ] button, then press the [ ] or [ ] button to change the setting. 1 Move the cursor to "ALARM TRIGGER" and press the [ ] button, then press the [ ] or [ ] button to change the setting. The maximum number of images (shown in parentheses) changes in accordance with the new settings. Maximum number of images [Setting conditions] When performing pre-alarm recording with a "FIELD" recording rate, short settings (i. e. , 60. 00 or 30. 00 FPS) cannot be made for "REC RATE". 48) When normal recording and pre-alarm recording are performed simultaneously, audio will not be recorded together with the pre-alarm recording image. When pre-alarm recording and normal recording are performed simultaneously with a multiplexer connected, the recording rate for pre-alarm recording should be set to a shorter rate than that for normal recording. [Settings] ( Setting ALARM indicates default setting. ) Description Performs alarm recording when an external alarm is generated (when a switch is attached to the alarm input terminal on the rear panel, and the switch is activated). 67) Performs alarm recording when both the external alarm and a motion sensor are activated simultaneously. SENSOR ALARM AND SENSOR ALARM OR Performs alarm recording when either the external alarm or a motion sensor is activated. SENSOR Although the image from a single camera may be recorded continuously when a short recording rate is set, a long rate can result in no images being recorded during normal recording. [Setting conditions] When sensor selection has been made (i. e. , "SENSOR", "ALARM AND SENSOR", or "ALARM OR SENSOR") it will be necessary to set the motion sensors. 67) 66 English 8 ALARM REC MODE SET [Settings] ( This unit's motion sensors cannot be used when a multiplexer is connected. When using the multiplexer's motion sensors, connect the alarm output on the multiplexer to this unit's alarm input. When using a multiplexer, connect its ground terminal and the recorder's ground terminal. Setting OFF 1 to 10 indicates default setting. ) Description Not carried out Motion sensing will be carried out. Lower values correspond to higher sensitivities. 4 Move the cursor to "EXIT", then press the [ ] or [ ] button to return to the <ALARM REC MODE SET> screen. Setting the motion sensor If a motion sensor is set on the monitor, alarm recording will be carried out when a moving subject is detected. 5 Press the [EXIT/OSD] button. 1 Move the cursor to "MOTION SENSOR" and press the [ ] button. The display returns to the normal screen. The motion sensor screen is displayed. If recording is ended during alarm recording using the motion sensor Set the sensitivity from the motion sensor screen to "OFF". (See the procedure 3. ) Motion sensor screen Pressing the [MENU RESET] button in the motion sensor screen sets the entire row in which the cursor is located. 2 Press the [ ] or [ ] button to select sensor operation positions (up to 80), then press the [ ] or [ ] button to confirm the selection. Press the [ ] or [ ] button to turn sensors "ON" (shown as ) and "OFF" (shown as ). Setting example 3 Move the cursor to "LEVEL", then press the [ ] or [ ] button to change the setting. English 67 1 DISPLAY/VIDEO LOSS SET <MAIN MENU 2> (6) Item ALARM TYPE VIDEO LOSS Setting ON OFF ON OFF Description Turns on display of the alarm type in the operation display area. "VIDEO LOSS!" is displayed when the camera image is interrupted. "VIDEO LOSS!" is not displayed, even when the camera image is interrupted. (7) Settings The <DISPLAY SET> screen lets you turn off the display of the date, time, or other information in the operation display area on the screen. [. . . ] After selecting the images to be printed, carry out procedure 1 above. The selected images will then be printed one by one. NETWORK OPERATION 11/05/2004 18:56:10 130 English 6 (when optional interface board is installed) DVR VIEWER Saving images In the case of images on a CD-R, the control panel includes buttons that can be used for saving images, so that images can be saved on another storage medium as described below. You can specify an existing folder to use or create a new folder, and you can also set your own filenames for the files being saved. 3 Specify the saving destination and the filename, and then click [Save]. The specified images will then be saved. The filenames for each image will be generated automatically based on the number of images being copied and the filename you entered. 1 Specify the start image and end image to be saved. Click [Set Copy Start image] and then use playback operations to select the start image. [. . . ]