User manual SANYO DS13390

[. . . ] This manual explains the installation of the PJ-Net Organizer and its operation. INSTALLATION and OPERATION of the PJNet Organizer OWNERS MANUAL Preparation Compliance Federal Communication Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 SANYO DS13390 of the FCC Rules. These limits are designed to provide Tested To Comply reasonable protection against harmful interference in a With FCC Standards residential installation. This equipment generates, uses FOR HOME OR OFFICE USE and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Next, please see chapter "Basic Setting and Operation" on page 22 It describes how to operate and set up the monitor . Completing of installation If you use a cable to connect the monitor and computer directly, without using a hub, you must use a UTP cross cable. In this case, you cannot access the login page if the setting of web browser is set to "Use proxy server". For further information, please see the "Web browser setting" of chapter "Appendix" on page 46. When you set up the network of monitor which has a default setting by using the computer, it must be carried out in the network which does not provide any gateways (routers). 15 Installation The Flash Player version 9 or later is required when you control the monitor. If your computer does not have, follow to the message on the control page to install the Flash Player. (http://www. adobe. com) Flash Player 16 Installation Configure the network of computer Configure the network of computer When you use the monitor through the network, the IP address of the monitor must have the same IP network number of the existing network. Also it is required to use the same IP network number of the computer to set up the monitor. In the network included with the gateway (router), it must be used with the IP network number specified by the gateway (router). Configure the computer's network by following steps: Windows 2000 This example explains how to set the following network address. IP Address : 192. 168. 0. 5 Subnet Mask : 255. 255. 255. 0 Gateway Address : 192. 168. 0. 1 1 Select 2 3 4 5 the Network and Dial-up Connections menu from [Start] - [Settings] menu. Click the Local Area Connection icon with right button of the mouse and then select the Properties menu from the popup menu. Select the Internet Protocol(TCP/IP) *1 on the General tab of the "Local Area Connection Properties" dialog window and then press the Properties button. * The entering User Name must be "user" and it cannot be changed. [Note] When accessing the monitor at first time or setting the no password [0000], the autologin will be performed and the next main setting page is displayed. Important If you have forgotton current network configuration(IP address, subnet mask, password DNS, and default gateway, you can set them to default value via serial port (RS232C) Refer to page 42 22 Login the setting page of the monitor 3 Display of setting page The following setting page of the monitor is displayed. The main menu which can be set up and control the monitor appears on the lower side of the page. On the setting page, the control and status items for selected menu are displayed. For further information, please see chapter "Controlling the monitor" on page 31. Sub Menu Setting Page Main menu 23 Basic Setting and Operation Initial Settings After installing this product onto the monitor, perform the following basic initial setting. Press the Initial Setting button on the main menu to display the initial setting page. The password can be set in this page. Password Setting This page is to set the password to restrict the access from an unauthorized person through the network. When you connect the monitor with this product to the network, you should set a password. Only a four-digit numeric number is valid characters for the password. 24 Network Configuration Network Configuration Press the Network Setting button on the main menu. This page is to set the IP Address, Subnet Mask, Default gateway, DNS (Domain Name Server) and Model ID. 1 Configure the network The IP address and Subnet Mask have been configured already in chapter "1: Installation" on page 7. If you want to change them or configure default gateway*1 or DNS*2, perform them in this page. Enter an applicable address number onto each parameter and press the Set button. [. . . ] Select an input source with radio button and press the Set button to change the input source. 2 Input 3 Wide Mode Click the Wide Mode on the sub menu. Select a wide mode with radio button and press the Set button to change the wide mode. The wide mode cannot be changed depending on the input signal. 35 Controlling the monitor 4 Other 1 Click the Other 1 on the sub menu. Select the item of Child Lock, RC Inhibition, or Power save with radio button and press the Set button to change these functions. The Child Lock, RC Inhibition, or Power save can be selected independently. 5 Other 2 Click the Other 2 on the sub menu. Press the Set button to set Auto PC function or return to factory setting condition. 36 Controlling the Monitor Make a memo This function can be used as a memo. [. . . ]