User manual SANYO DP50719

[. . . ] Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK); NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. [. . . ] The TUNING menu will appear. CLOCK PROGRAM TUNING SETUP SELECT ENTER TO EXIT PRESS 3 Press E to choose the SOURCE SELECT item, then press F or G to select TUNER. AUTO CHANNEL SET TUNING BAND: TV CH. 2 ADD SOURCE SELECT: TUNER Press F or G repeatedly to switch between TUNER and LINE. 4 Press SELECT ADJUST TO EXIT PRESS D or E to choose the AUTO CHANNEL SET item, then press F or G to set the channel. The tuner will automatically cycle through all available channels in the area and place them in the tuner's memory. AUTO CHANNEL SET TUNING BAND: TV CH. 2 ADD SOURCE SELECT: TUNER 5 After the AUTO CHANNEL SET PROCEEDING is complete, make sure the TUNING BAND is set appropriately (TV or CATV) by pressing D or E and choosing the correct TUNING BAND (TV or CATV) by pressing F or G using the TUNING menu. · Remember, TV is for the air antenna reception, CATV is for cable or wireless cable connection. SELECT ADJUST TO EXIT PRESS AUTO CHANNEL SET TUNING BAND: TV CH. 2 ADD SOURCE SELECT: TUNER SELECT ADJUST TO EXIT PRESS 6 Press MENU to return to the TV screen. Use CH/TRACK (v/w) or CHANNEL (v/w) on the front panel to cycle the VCR through the channels in memory. AUTO CHANNEL SET PROCEEDING CHANNEL 13 TO EXIT PRESS AUTO CHANNEL SET TUNING BAND: TV CH. 2 ADD SOURCE SELECT: TUNER SELECT ADJUST TO EXIT PRESS 17 CHANNEL SELECTION (Cont'd) MAIN MENU CLOCK PROGRAM TUNING SETUP SELECT ENTER TO EXIT PRESS TO ADD OR ERASE CHANNELS FROM MEMORY This feature allows you to add or erase channels from memory manually. 1 Press MENU and the MAIN menu will appear. The TUNING menu will appear. TUNING MENU PREPARATION 3 Press E to choose the CH. 2 ADD SOURCE SELECT: TUNER select a channel to add or erase. 4 Press ENTER to add or erase the channel. Repeat steps 3 and 4 to add or erase channels. ADD/DELETE SELECT ADJUST TO EXIT PRESS 5 Press MENU to return to the TV screen. VIEWING TV ONLY Switch on the TV and set it to the channel that you wish to watch. You don't need to disconnect the VCR from the TV to watch TV separately. When the VCR's power is OFF, or when the VCR's power is ON and the TV/VCR selector is set to TV, the TV will operate as if it were connected directly to the antenna or cable. NOTES POWER STOP/ EJECT CHANNEL P Set POWER to OFF. · The power cord must be plugged into an AC outlet. · To view or record cable TV programs with the VCR, the VCR's TUNING BAND item must be set to CATV (TUNING menu). This may cause interference in the picture and sound (of the VCR) during the recording or playback mode. In this case we recommend that you set the clock manually. 6 Press MENU when finished. 7 Turn off the VCR and the auto clock setting works. 20 SETTING THE CLOCK (Cont'd) MAIN MENU CLOCK PROGRAM TUNING SETUP SELECT ENTER TO EXIT PRESS MANUAL CLOCK SET Example: July 5, 2001 ; 2:15 AM 1 Press MENU and the MAIN menu will appear. 2 Press D or E to choose the CLOCK menu. Press ENTER and the CLOCK menu will appear. CLOCK SET MENU MONTH : JANUARY DAY : 1 MON YEAR : 2001 TIME : 12 : 00 AM AUTO CLOCK SET : ON DAYLIGHT SAVING: AUTO TIME ZONE: AUTO 3 Press F or G to choose the month. The day of the week will display automatically. PREPARATION SELECT ADJUST TO EXIT PRESS MONTH : JULY DAY : 5 THU YEAR : 2001 TIME : 12 : 00 AM AUTO CLOCK SET : OFF DAYLIGHT SAVING: AUTO TIME ZONE: AUTO 5 Press E to choose the YEAR item. Press F or G to choose the year. SELECT ADJUST TO EXIT PRESS 6 Press E to choose the TIME item. Press F or G to choose the time. MONTH : JULY DAY : 5 THU YEAR : 2001 TIME : 12 : 00 AM AUTO CLOCK SET : OFF DAYLIGHT SAVING: AUTO TIME ZONE: AUTO 7 Press E to choose the DAYLIGHT SAVING item. Press or G to choose the ON or OFF. F SELECT ADJUST TO EXIT PRESS 8 Press MENU when finished. MONTH : JULY DAY : 5 THU YEAR : 2001 TIME : 2 : 15 AM AUTO CLOCK SET : OFF DAYLIGHT SAVING: AUTO TIME ZONE: AUTO NOTE SELECT ADJUST TO EXIT PRESS The "AUTO CLOCK SET" must set to "OFF". If set to "ON", an incorrect date and/or time will be entered again when the VCR is turned off. MONTH : JULY DAY : 5 THU YEAR : 2001 TIME : 2 : 15 AM AUTO CLOCK SET : OFF DAYLIGHT SAVING: ON TIME ZONE: AUTO SELECT ADJUST TO EXIT PRESS 21 NORMAL PLAYBACK PREPARATION · Turn on the TV. · If a direct VIDEO/AUDIO connection is made between the VCR and the TV, set the TV's source selector to VIDEO. NORMAL PLAYBACK 1 Insert a prerecorded video cassette. The TAPE IN indicator will light and the VCR will power-up automatically. · Make sure that the TIMER indicator in the VCR indicator panel is not lighted. · If a tape without a safety tab is inserted the unit will start the playback automatically. POWER 1 4 7 SLOW EJECT 2 5 8 0 3 TV/VCR 6 Ad JUMP 9 INPUT SP/SLP REC 2 Press PLAY once. The PLAY appears on the TV screen . · In playback, the TV/VCR selector switches to VCR mode automatically. PAUSE PLAYBACK REW PLAY STOP FF MENU CH TRACK CLK/COUNT ENTER 3 Press STOP to stop playback. CLEAR TV CH TV CH TV INPUT VOL VOL TV POWER The STOP appears on the TV screen. · If the tape reaches the end before STOP is pressed, the VCR will automatically stop, rewind, eject, and it will turn itself off. TRACKING CONTROL AUTO TRACKING The automatic tracking function adjusts the picture to remove snow or streaks. [. . . ] 6 Press REW. The tape automatically stops when the tape counter returns to about "0:00:00". TV POWER TV INPUT ADDITIONAL INFORMATION TAPE REMAINING TV Screen This function allows the time of the remaining tape to be displayed during recording or playback. Press CLK/COUNT until the REM indicator displays on the TV screen during recording or playback. NOTE REM 1:07 The remaining tape length indicator may not be displayed correctly depending on the condition of the tape and the kind of the tape (T-140, T-160, or T-210 etc) 33 EDITING A RECORDING 1 Press PLAY and watch the program until you reach the exact point where you want the new recording to start. POWER 1 4 7 SLOW EJECT 2 5 8 0 3 TV/VCR 6 Ad JUMP 2 Press PAUSE. 4 When you wish to start recording, press PAUSE again. The new program material will directly follow the previously recorded material. This feature is especially helpful during camcorder-to-VCR dubbing use so each segment of the recording becomes a continuous program. 9 INPUT SP/SLP REC PAUSE REW PLAY STOP FF MENU CH TRACK CLK/COUNT ENTER OPERATING HINTS · In manual recording, Timer recording, Instant Timer Recording, playback, or fast forward modes, the VCR automatically starts rewinding the tape at the end of the tape. [. . . ]