User manual SANYO DMP-P7

[. . . ] Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. (for example: main plug is used as the connection, so it should always remain ready operate. ) Minimum distances around the apparatus for sufficient ventilation; Before scrapping the appliance, remove the batteries and place them in the appropriate battery collection container. Batteries (battery pack or batteries installed) shall no excessive heat such as sunshine, fire or the like. Do not install this equipment in a confined space, such as a bookcase or built in cabinet. Before operating the system, check that the operating voltage indicated on the model plate at your system bottom is identical with the voltage of your local power supply. [. . . ] 29. POWER ON/OFF Button MUTE Button PRESET Button SLEEP PROG Button BAND/RADIO Button ST/MONO Button Turns clock radio ON or OFF or reset alarm when alarm is sounding Mutes the sound Selects preset radio stations Selects sleep function Stores radio program This button switches between AM and FM radio bands. Skip to previous or next track when iPod is playing, or HOLD to scan current playing track. VOLUME + Button 6 Clock Display AM Indicator TIME/ALARM Display Alarm 2 Armed Alarm 1 Armed iPod Indicator Wake To Indicator: iPod, Radio, Buzzer, SHUFFLE Indicator PRESET Indicator ST/KHz/MHz FM Indicator SLEEP Indicator Indicator PM Indicator Radio Frequency/Date/ Volume Level/AUX Display 7 Setting Up the Clock Radio Setting Clock Time and Calendar 1. Press and hold the CLOCK Button located on the back of the unit until 12H or 24H appeared. Select your desired clock display either 12 hour or 24 hour by pressing SKIP FORWARD or BACKWARD Button repeatedly. Press the SKIP FORWARD or BACKWARD Button to set the current time, then press the CLOCK Button again to confirm clock setting. (Note: if the system is set to 12hour mode, if it's afternoon, the PM indicator will be lighted on. ) 3. Press the CLOCK Button to accept the current setting, or press the SKIP FORWARD or BACKWARD Button until current year is displayed. Press the CLOCK Button to accept the current setting or press the SKIP FORWARD or BACKWARD Button until current date is displayed. Press the CLOCK Button to confirm date setting. Setting Alarm Time 1. Press and hold the ALARM 1 Button or ALARM 2 Button until the display flashes. Press the SKIP FORWARD or BACKWARD Button until the desired alarm time is displayed. Remember to set the correct AM or PM (an icon to the right of the time display is the PM indicator). Press the WAKE Button to select the iPod, radio or alarm buzzer hi or low to wake to. Press and hold ALARM 1 or ALARM 2 Button until clock display flashing, press ALARM 1 or ALARM 2 Button again. Press the ALARM 1 Button or ALARM 2 Button again to exit the setting mode. Note: Once you set the alarm time, the alarm will be automatically armed. The Alarm Icon and Wake Icon will appear to indicate the alarm is armed. Press the PLAY/PAUSE Button on the clock radio (or PLAY/PAUSE Button on the remote control). Press the VOLUME UP or DOWN on the clock radio (or Volume+ and Volume- Button on the remote control) to adjust the system volume. To turn off the unit, press the POWER Button (or POWER ON/OFF Button on the remote control). Please remember to turn off your device, too. Listening to Radio Note: Extend FM wire antenna fully for best FM reception (do not strip, alter or attach to other antennas). [. . . ] For details visit http://www. apple. com/ipod/download Please make sure your iPod is working properly before docking into the unit. Please refer to your iPod manual for details. Unit doesn't respond AC cord isn't plugged into a wall (no power) outlet. Wall outlet is not functioning iPod does not dock properly Using no or wrong iPod insert iPod didn't install properly iPod does not respond to the unit iPod is not installed properly Your iPod software is too old iPod is locked up Using 1st or 2 nd generation iPod, other devices. Clock radio cannot control those iPods or other devices. 13 Troubleshooting Symptom iPod didn't charge up Possible Problem iPod is not installed properly iPod is locked up/frozen No AM band radio sound but others OK Solution Remove your iPod from the dock and check for obstruction on the connectors in the dock and on your iPod. Please make sure your iPod is working properly before docking into the unit. [. . . ]