User manual SANYO DAS-201

[. . . ] OWNER`S INSTRUCTION MANUAL Model DAS 201 Fully Digital Answering System Please read this operation manual before using your new telephone and keep it for further reference QUICK INSTRUCTIONS · Setting the Time ­ Press `STOP/TIME' to enter the setting mode ­ Then Press the FF Key or the REPT Key to adjust the Weekday ­ Press `STOP/TIME' again to set the Weekday ­ Repeat to set Hours and Minutes · Playing the Current Time ­ Press `STOP/TlME' · Recording the Outgoing Message (OGM) ­ Press `OGM1' ­ Speak clearly into the microphone with your message ­ Press `STOP/TIME' to stop recording ­ Repeat the process for `OGM2' · Recording a Memo ­ Press `MEMO/2WAY' for 2 seconds ­ Speak clearly into the microphone with your message ­ Press `STOP/TIME' to stop recording ·2 ­ ­ ­ Way Recording Press `MEMO/2WAY' for 4 seconds Speak into your telephone in a normal fashion Press `STOP/TIME' to stop recording QUICK INSTRUCTIONS CONT'D 4. Repeat Message Press `REPT ' once to replay current message, twice to replay the previous message Any one of the following keys will resume Playback: PLAY/FF / REPT /ERASE/STOP Press `ERASE' Press `STOP/TIME' Press and Hold `ERASE' to erase ALL Messages To restore or save all messages, Press and Hold `ERASE' again. 5. Erase and Save ALL Messages · Security Code Remote Control ­ Refer to "Remote Control Functions Table" on Page 11/12. · Playing a Memo ­ Press `MEMO/2WAY' · Setting to Answer/Record Mode or Answer Only Mode ­ If system is in Answer Only Mode, Press `ANSWER' for about 2 seconds. ­ The DAS 201 will beep and OGM2 will play · Playing Messages 1. [. . . ] · If you are not satisfied with the message, repeat this process and rerecord your message. This is used when you prefer not to take messages, and is automatically activated if the DAS 201's memory is full. To record an OGM2 message, follow the above instructions, using the OGM2 button in place of the OGM1 button. Playing your Outgoing Message (OGM) ­ To play your OGM, simply press and release the `OGM1', or `OGM2' buttons. Recording a Memo ­ The DAS 201's Memo function allows you to leave a message for another member of your business or household, when you are going to be away. Complete the following steps to record your Memo message: · Press the `MEMO/2WAY' key, and hold it for approximately 2 seconds. 8 OPERATING INSTRUCTIONS CONT'D After a short beep, the LED will display `00'. · At the end of the beep, speak in a clear voice, directly into the microphone. Recording a Two-Way Conversation ­ The DAS 201's 2-Way Record function allows you to record important conversations you have on the telephone. Complete the following steps to use the 2-Way Record function: · Press the `MEMO/2WAY' key, and hold it for approximately 4 seconds. · The LED will display `2R' and 2-Way Recording will begin. · At the end of your conversation, or when you wish to stop recording, simply press the `STOP/TIME' key. Playing Memos and 2 Way Conversations ­ To play these messages, press the `MEMO/2WAY' key. Setting to Answer/Record Mode or Answer Only Mode ­ Note: When power is on, system is always in either one of these 2 modes. · If system is in Answer Only Mode, Press `ANSWER' for about 2 seconds. Ring and Toll Saver ­ The DAS 201 will normally begin recording an incoming call after the second ring. However, if there are no unplayed messages on the system, the DAS 201 will not answer until after the fourth ring. This feature allows you to call into your answering machine, and determine, without a toll, if there are any unplayed messages on the system (i. e. Recording Incoming Calls ­ When the DAS 201 is in Answer/Record mode, it will answer the telephone after the second (or fourth) ring, then will play your OGM1 message. At the end of the OGM1 message a beep will sound, indicating to your caller that they may begin speaking. At the end of the message, the DAS 201 will sound a long beep, indicating that the recording time is over. 9 OPERATING INSTRUCTIONS CONT'D K. Playing All Messages ­ The LED will display the total number of messages in the DAS 201's memory. The following details the playback procedures: · Playback Press `PLAY' · Pause Message Press `PLAY' · Resume Playback from Pause Any one of the following keys will resume Playback: PLAY/FF /REPT / ERASE/STOP · Repeat Message Press `REPT `once to replay current message, twice to replay the previous message. [. . . ] Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telec ommunications company cause to request the user to disconnect the equipment. " CAUTION: "Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. " "Notice: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. " The REN assigned to this device is 0. 3. · · · · · CARE Keep the unit dry. Doing so might invalidate the TAD's warranty and void your Industry Canada authorization to operate it. [. . . ]