User manual SANYO CLT9920 INSTRUCTION MANUAL

[. . . ] CLT9920 (SANYO) A5 2nd 6/29/00 10:06 AM Page 1 INSTRUCTION MANUAL CLT-9920 900-MHz Digital Spread Spectrum Cordless Telephone IMPORTANT Charge the handset battery pack for 15 hours before using your cordless handset for the first time. www. sanyocanada. com Français au verso CLT9920 (SANYO) A5 2nd 6/29/00 10:06 AM Page 2 Introduction Congratulations on your purchase of the CLT-9920 cordless telephone. This phone is designed for reliability, long life, and outstanding performance utilizing the latest in 900 MHz Digital Spread Spectrum technology. Note: Some illustrations in this manual may differ from the actual unit for explanation purposes. Features q 900 MHz Digital Spread Spectrum Technology q Lighted Handset Keypad q 10 Number Memory Dialing q Last Number Redial q 7-Day Standby Battery Life/6-Hour Talk Time q 20-Channel Auto/Manual Scan q Pulse/Tone Dialing q Page/Handset Locator q Mute q Auto Talk and Auto Standby q Handset Earpiece and Ringer Volume Control q Belt Clip and Headset Jack q Wall-Mountable q Hearing Aid Compatible 900-MHz Digital Spread Spectrum Technology utilizes a "wider frequency band" vs. [. . . ] Press MEMORY and a number (0­9) for the memory location you wish to use. You hear a long beep and the TALK/BATT LOW indicator goes out indicating the number has been stored successfully. E6 CLT9920 (SANYO) A5 2nd 6/29/00 10:06 AM Page 8 Dialing a Stored Number To dial a phone number stored in memory, press TALK/END, then press MEMORY and the memory location (0­9) number. If you select a memory location that does not have a stored number, the handset will beep rapidly and the phone will not dial. Selecting a Different Channel If you encounter interference while using your phone, you can manually change the channel for clearer communication by pressing the SCAN button. The SCAN button on the handset allows you to choose from 20 factory-set channels. During the course of a conversation, if you hear static or noise which makes it difficult to hear, press SCAN. As you travel further out of range, the voice transmission will begin to break up. If you pass the range limits of the base, your call will terminate. E7 CLT9920 (SANYO) A5 2nd 6/29/00 10:06 AM Page 9 Installing the Belt clip Installing the belt clip w To attach the belt clip Insert the belt clip into the holes on each side of the handset. To use this feature, simply plug any standard shielded headset with a 2. 5-mm plug into the headset jack. Headset installation w To remove the belt clip Pull both sides of the belt clip to release the tabs from the holes. headset jack If you have wall-mounted the base, you must remove the belt clip to charge the handset with the keypad facing forward. Not all headsets are the same. Some headsets may lower volume levels or performance of the phone. Troubleshooting If your cordless telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact your place of purchase or call SANYO SOS Helpline. Caution: Do not attempt to service this unit yourself. Problem CHARGE/IN USE LED won't come on when handset is placed in base. Weak and/or scratchy sound · · · · Suggestion Make sure the AC adaptor is plugged into the base and wall outlet. Make sure the rechargeable battery pack is properly connected in the handset. Make sure that the charging contacts on the handset and on the base are clean. · Make sure that the base antenna is in the vertical position. · Interference by other electronics equipment such as TVs, computers, microwaves, fluorescent lighting, etc. · · · · Check both ends of the telephone line cord. Reset the security code by placing the handset back on the base for a few seconds. The CHARGE/IN USE LED will blink indicating that the phone has been reset. Can't make or receive calls. Handset doesn't ring or receive a page. · The Nickel-Cadmium battery pack may be weak. · Reset the security code by placing the handset back on the charging cradle for a few seconds. The CHARGE/IN USE LED will blink indicating that the phone has been reset. E8 CLT9920 (SANYO) A5 2nd 6/29/00 10:06 AM Page 10 Technical Information REN Number: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The REN number of this unit is located on the bottom of the base unit. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. NOTICE: Privacy of communications may not be ensured when using this telephone. [. . . ] Our friendly and knowledgeable product specialists will quickly answer your questions about setup and use of Sanyo telephone products. Simply call toll free from anywhere in Canada to connect to our no-charge, SOS support and service network. 1-800-263-2244 between 10:00 AM ­ 7:00 PM EST Stay-At-Home Convenience It's a nuisance making another trip to the store when you're stuck. Now with SOS, all that's necessary is a quick call from your home for product assistance or exchange. [. . . ]