User manual SANYO CLT9901 INSTRUCTION MANUAL

[. . . ] CLT9902 #4 (SANYO) 8/11/00 4:14 PM Page 1 INSTRUCTION MANUAL CLT-9902 CLT-9901 900-MHz Cordless Telephone NOISE REDUCTION IMPORTANT Charge the handset battery pack for a full 15 hours before using your cordless handset for the first time. Français au verso CLT9902 #4 (SANYO) 8/11/00 4:14 PM Page 2 Introduction Your Sanyo 900-MHz COMPANDER PLUS cordless telephone is a fine-quality home communications product. It is carefully designed and produced by a world leader of consumer and industrial electronics equipment. With proper maintenance and care, it will provide you with years of enjoyment and convenience. COMPANDER PLUS Noise Reduction This fourth generation of the Sanyo's original noise reduction technology now filters out more background noise. Other Features G G G G G G G G G G G G G 900-MHz Technology Superior Range - The use of 900-MHz frequency band for signal transmission between base and handset means greater communication range compared to conventional 43--49 MHz cordless telephones. In normal situations, approximately 4 times greater distance can be achieved. [. . . ] If you select any keys other than 0­9, the handset will beep rapidly and no number will be stored. E6 3 CLT9902 #4 (SANYO) 8/11/00 4:14 PM Page 8 Dialing a Stored Number To dial a phone number stored in memory, press TALK/END, then press MEMORY and the memory location (0­9) number. You hear a long beep confirming that you have erased the number. Replacing a Stored Number Your phone has 10 memory locations, represented by the numbers 0­9 on the keypad. If you store a phone number in one of these locations and attempt to store a different number in the same location later, the new number will replace the previous one. Travelling Out of Range When you begin to move too far from the base, you will first hear a clicking sound. As you travel further out of range, the voice transmission will begin to break up. If you pass the range limits of the base, your call will terminate. E7 CLT9902 #4 (SANYO) 8/11/00 4:14 PM Page 9 Belt Clip and Headset Jack (Available on CLT-9902 only) Installing the belt clip (CLT-9902 only) M To attach the belt clip Insert the belt clip into the holes on each side of the handset. Press down until it clicks. Headset installation (CLT-9902 only) Your phone may be used with an optional headset for handsfree operation. To use this feature, simply plug any standard shielded headset with a 2. 5-mm plug into the headset jack. M To remove the belt clip Pull both sides of the belt clip to release the tabs from the holes. If you have wall-mounted the base, you must remove the belt clip to charge the handset with the keypad facing forward. headset jack Troubleshooting If your cordless telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact your place of purchase or call SANYO SOS Helpline. Caution: Do not attempt to service this unit yourself. Servicing must be performed by qualified personnel. Problem CHARGE/IN USE won't come on when handset is placed in base. Suggestion · Make sure the AC adapter is plugged into the base and wall outlet. · Make sure the rechargeable battery pack is properly connected in the handset. · Make sure that the charging contacts on the handset and on the base are clean. · Interference by other electronics equipments such as TVs, computers, microwaves, fluorescent lighting, etc. · · · · Check both ends of the telephone line cord. Reset security code by placing the handset back on the base for a few seconds. The CHARGE/IN USE indicator will blink when the phone has been reset. Weak and/or scratchy sound Can't make or receive calls. Handset doesn't ring or receive a page. · The Nickel-Cadmium battery pack may be weak. · Reset security code by placing the handset back on the charging cradle for a few seconds. The CHARGE/IN USE indicator will blink when the phone has been reset. E8 CLT9902 #4 (SANYO) 8/11/00 4:14 PM Page 10 Technical Information Ren Number: 0. 4 The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. [. . . ] Now with SOS, all that's necessary is a quick call from your home for product assistance or exchange. SOS ­ it's the ultimate in convenience. Hassle-Free Exchange Should your Sanyo telephone/telephone with answering system require servicing during the warranty period, SOS will have a free replacement unit at your door within 48 hours. * For security reasons, you will be asked to give us your credit card number (VISA or MasterCard). Guaranteed Quality All SOS replacement sets are checked and serviced by factory-authorized technicians before being sent out. SOS means you never have to worry. With SOS, we've got you covered! * Two business days required E10 CLT9902 #4 (SANYO) 8/11/00 4:14 PM Page 12 The SANYO Comfort Warranty WARRANTY APPLICATION Sanyo Communications products purchased new, unused in Canada through a Sanyo Authorized Dealer are warranted against manufacturing defects in materials and workmanship for ONE YEAR covering parts and labour, from the date of purchase by the original retail purchaser. This warranty only applies in favour of the original retail purchaser of the warranted product. [. . . ]