User manual SANYO CLT-A5830

[. . . ] INSTRUCTION MANUAL CLT-A5830 Dual Handset Models 5. 8 GHz Cordless Telephone with Caller ID & Visual Call Waiting CLT-A5822 CLT-A5832 The picture depicts dual handset model Important Charge the handset battery for 12 continuous hours prior to first use. www. sanyo. ca 1 sy5822 10 april. p65 1 2006/5/12, ¤U¤È 02:52 TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Checking package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Press MUTE/FORMAT once to add the area code (Note: The programmed area code must match the Caller ID area code). · Press MUTE/FORMAT a third time to go back to the 7-digit number. 16 sy5822 10 april. p65 16 2006/5/12, ¤U¤È 02:52 CALLER ID FEATURES Storing Caller ID entries in the directory Before storing a caller ID number, make sure the number appears in proper digits for your dialing area. For example, if the Caller ID number appears 1-416-222-5555 but it is not a long distance number, press MUTE/FORMAT until it shows 416-222-5555 (without 1). Note: If a specific memory entry is longer than 15 digits, the last 15 digits show on the screen. Use the CID/VOL Press MEM key, "MEMO # --" shows on the top right corner of screen. If the memory location already contains name and number information, "REPLACE MEMO?" will show on screen. Press *TONE/EXIT button to return unit to standby mode without saving. If the selected memory location is empty, you will hear a confirmation tone when the new memory record is saved. Note: If the selected CID record contains non-digit characters, or the number is more than 24 digits, the unit will not store the record. Use MUTE/FORMAT key to display the phone number in proper digits if necessary. 4. The number dials automatically. Deleting entries from the Caller list Use CH/DEL to erase the entry currently shown on screen or all entries. Deleting the displayed entry 1. Confirmation tone sounds and LCD shows "DELETED" for 2 seconds. 17 sy5822 10 april. p65 17 2006/5/12, ¤U¤È 02:52 CALLER ID FEATURES Deleting all entries 1. "NO CALLS" shows on screen. DIRECTORY You can store up to 10 names (up to 15 characters) and numbers (up to 24 digits) in the directory for quick dialing. If a number exceeds 24 digits, you can program it in parts, and then chain dial the number. Storing a number in the directory To program a number to memory: 1. Select the desired memory location (0 ­ 9) or use the CID/VOL or keys to find an empty memory location. Within 1 second, you can press the same key again to select another character. If you make a mistake, press CH/DEL to delete previous characters one by one. Key Press 1st ­ 5th press 2 ­ 6 press nd rd th 1 2 A 3 D E F ) 4 G H I $ 5 J K L ' 6 M N O ; 7 P Q R S 8 T U V ? 9 W X Y Z ­ * ! B C ( 3 ­ 7 press th 4th ­ 8th press 6. If you make a mistake, press CH/DEL to delete previous digits one by one, then enter the correct digits. If you wish to add a pause, press PAUSE two times at the desired location. Be sure to press it twice, or you will enter a # (number sign) 18 sy5822 10 april. p65 18 2006/5/12, ¤U¤È 02:52 DIRECTORY and not a pause. Or you can store redial number in the directory by pressing REDIAL (Note: If the redial number is longer than 24 digits, it cannot be stored into the memory. ). If you are replacing a number, "REPLACE MEMO?" shows on screen. [. . . ] NOTICE: This equipment meets the applicable Industry Canada Terminal TECHNICAL INFORMATION 31 sy5822 10 april. p65 31 2006/5/12, ¤U¤È 02:52 TECHNICAL INFORMATION Equipment Technical Specifications. The abbreviation, IC, before registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. SANYO COMFORT WARRANTY WARRANTY APPLICATION SANYO Communications products purchased new, unused in Canada through a SANYO Authorized Dealer are warranted against manufacturing defects in materials and workmanship for ONE YEAR covering parts and labour, from the date of purchase by the original retail purchaser. This warranty only applies in favour of the original retail purchaser of the warranted product. WHAT IS NOT COVERED a. [. . . ]