User manual SANYO CLT-2410

[. . . ] CLT2410 (SANYO) A5 2nd 7/18/00 6:41 PM Page 1 INSTRUCTION MANUAL CLT-2410 2. 4-GHz Digital Spread Spectrum Cordless Telephone IMPORTANT Charge the handset battery pack for 15 hours before using your cordless handset for the first time. www. sanyocanada. com Français au verso CLT2410 (SANYO) A5 2nd 7/18/00 6:41 PM Page 2 Introduction Congratulations on your purchase of the CLT-2410 cordless telephone. This phone is designed for reliability, long life, and outstanding performance utilizing the latest in 2. 4-GHz Digital Spread Spectrum technology. Note: Some illustrations in this manual may differ from the actual unit for explanation purposes. Features q 2. 4-GHz Digital Spread Spectrum Technology q Lighted Handset Keypad q 10-Number Memory Dialing q Last Number Redial q 7-Day Standby Battery Life/6-Hour Talk Time q 30-Channel Auto/Manual Scan q Pulse/Tone Dialing q Page/Handset Locator q Mute q AutoTalk and Auto Standby q Handset Earpiece and Ringer Volume Control q Belt Clip and Headset Jack q Wall-Mountable q Hearing Aid Compatible 2. 4-GHz Digital Spread Spectrum Technology utilizes a "wider frequency band" vs. [. . . ] If you select a memory location that does not have a stored number, the handset will beep rapidly and the phone will not dial. Selecting a Different Channel If you encounter interference while using your phone, you can manually change the channel for clearer communication by pressing the SCAN button. The SCAN button on the handset allows you to choose from 30 factory-set channels. Press TALK/END again if you do not wish to make a call. Travelling Out of Range When you begin to move too far from the base, you will first hear a clicking sound. As you travel further out of range, the voice transmission will begin to break up. If you pass the range limits of the base, your call will terminate. E7 CLT2410 (SANYO) A5 2nd 7/18/00 6:41 PM Page 9 Installing the Belt clip Installing the belt clip w To attach the belt clip Insert the belt clip into the holes on each side of the handset. Press down until it clicks. Headset installation Your phone may be used with an optional headset. To use this feature, simply plug any standard shielded headset with a 2. 5-mm plug into the headset jack. w To remove the belt clip Insert a standard flat head screwdriver into a notch of the belt clip, then remove the belt clip as shown below. If you have wall-mounted the base, you must install the belt clip to hold the handset in the proper charging position. Do not hang the handset with the keypad facing inside. headset jack Not all headsets are the same. Some headsets may lower volume levels or performance of the phone. Troubleshooting If your cordless telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact your place of purchase or call SANYO SOS Helpline. Caution: Do not attempt to service this unit yourself. Problem Suggestion CHARGE/IN USE indicator · Make sure the AC adaptor is plugged into the base and wall outlet. won't come on when handset · Make sure the handset is properly seated in the base. · Make sure the rechargeable battery pack is properly connected in the handset. · Make sure that the charging contacts on the handset and on the base are clean. Weak and/or scratchy sound · Make sure that the base antenna is in the vertical position. · Interference by other electronics equipment such as TVs, computers, microwaves, fluorescent lighting, etc. · · · · Check both ends of the telephone line cord. Reset the security code by placing the handset back on the base for a few seconds. The CHARGE/IN USE indicator will blink indicating that the phone has been reset. Can't make or receive calls. Handset doesn't ring or receive a page. · The Nickel-Cadmium battery pack may be weak. · Reset the security code by placing the handset back on the charging cradle for a few seconds. The CHARGE/IN USE indicator will blink indicating that the phone has been reset. E8 CLT2410 (SANYO) A5 2nd 7/18/00 6:41 PM Page 10 Technical Information REN Number: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. [. . . ] Our friendly and knowledgeable product specialists will quickly answer your questions about setup and use of Sanyo telephone products. Simply call toll free from anywhere in Canada to connect to our no-charge, SOS support and service network. 1-800-263-2244 between 10:00 AM ­ 7:00 PM EST Stay-At-Home Convenience It's a nuisance making another trip to the store when you're stuck. Now with SOS, all that's necessary is a quick call from your home for product assistance or exchange. [. . . ]