User manual SANYO CLT-2402

[. . . ] CLT-2412E-NEW 7/16/02 9:09 AM Page 1 2. 4 GHz Cordless Telephone with Caller ID Instruction Manual CLT-2402 CLT-2412 Important Charge the handset battery for 12 continuous hours prior to first use. SANYO Canada Inc. www. sanyocanada. com CLT-2412E-NEW 7/16/02 9:09 AM Page 2 TABLE OF CONTENTS INTRODUCTION . Replacing a directory entry with a Caller ID entry Changing a stored name/number . 16 The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. 2 3 CLT-2412E-NEW 7/16/02 9:09 AM Page 4 INTRODUCTION Congratulations on your purchase of this Sanyo cordless telephone. [. . . ] Caution: · Use only the specified battery type (3. 6 V, 600 mAh). · Never throw the battery into a fire, disassemble it, or heat it. · Remove battery if storing the phone over 30 days. RECYCLING NICKEL-METAL HYDRIDE BATTERIES NICKEL-METAL HYDRIDE BATTERIES MUST BE DISPOSED OF PROPERLY. Please take your used battery pack to a store that recycles Ni-MH batteries. POWER FAILURE During the period that the power is off, you will not be able to make or receive calls with the telephone. After a power outage, place the handset in the base for about 20 seconds to reset the digital security code. Make sure the telephone is off before you replace the battery. Disconnect the battery plug from the jack 1 in the compartment and remove the battery pack. Note: If the handset battery is removed for more than 5 minutes, the directory memory and Caller ID memory will be erased. Charge the handset battery for 12 continuous hours prior to first use. Caution: To reduce the risk of fire or personal injury, use a 3. 6 V, 600 mAh battery. Replacement part number: GES-3AHRAAAU. HEADSET JACK AND BELT CLIP Headset connection (Headset not included) For hands free conversation, connect the headset (not included) to the HEADSET jack. The handset earpiece and microphone are disabled when the headset is connected. · Press TALK to answer or place a call while using the headset. Belt clip installation · Attach the belt clip by inserting the sides of the belt clip into the slots. Snap the ends of the belt clip into place. · 20 21 CLT-2412E-NEW 7/16/02 9:09 AM Page 22 LCD SCREEN MESSAGES The following indicators show the status of a message or of the phone. ERROR ERROR Single Tone Two Long Beeps Caller information has been interrupted during transmission or the phone is excessively noisy. A long warbling tone SOUND SIGNALS Signals an incoming call A key is pressed Confirmation tone One short beep and one long beep Three short beeps 4 short beeps every 7 seconds Page signal ENTER NAME ENTER NAME Prompt telling you to enter name in directory. Error tone/Out-of-range warning Low battery warning DELETE ALL?DELETE ALL? Prompt asking you if you want to erase all Caller ID entries. TROUBLESHOOTING CALLER ID DELETE? Prompt asking you if you want to erase the current Caller ID entry or a directory entry that is shown on the screen. END OF LIST END OF LIST Indicates that there is no additional information in Caller ID list. NEW Indicates call or calls have not been reviewed. UNKNOWN NUMBER/UNKNOWN NAME/UNKNOWN CALLER UNKNOWN NUMBER/UNKNOWN NAME/UNKNOWN CALLER The incoming call is from an area not serviced by Caller ID, or the information was not sent. PAGING Someone has pressed the PAGE key on the base. No Display · Is battery fully charged?· Make sure that the base is connected to a non-switched AC outlet. · Did you order Caller ID service from your local telephone company?The display will not work unless you order Caller ID service from your phone company. Caller ID Error Message · The phone displays this message if it detects anything other than valid Caller ID information during the silent period after the first ring. This message indicates either the presence of noises on the line, or that an invalid message has been sent from the telephone company. BLOCKED NUMBER/BLOCKED NAME/BLOCKED CALLER The person is calling from a number that has been blocked from transmission. TELEPHONE NO DATA No Caller ID information was received. No dial tone · Check installation: - Is the base power cord connected to a working outlet?- Is the telephone line cord connected to the base unit and the wall jack?· Disconnect the base from the wall jack and connect another phone to the same jack. If there is no dial tone in the second phone, the problem might be your wiring or local service. · Make sure the battery is properly charged (12 continuous hours). · Is the battery pack installed correctly? 22 23 CLT-2412E-NEW 7/16/02 9:09 AM Page 24 TROUBLESHOOTING · Did the handset beep when you pressed TALK/CALL BACK? [. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. connections themselves, but should contact the appropriate electrical inspection authority, or electrician, as appropriate. d. SANYO COMFORT WARRANTY Communications products not intended for Canadian usage or products without appropriate Canadian regulatory approvals. Accessory items including antenna, and batteries, Damage in or due to transportation. [. . . ]