User manual SANYO AVM-3680G

[. . . ] * The contents of this manual are subject to change without notice. 2 Contents Chapter 1 Introduction. . 27 PJ Master Owner's Manual 3 Contents IP Address setting . . 51 4 Chapter 1 Introduction 1 PJ Master Owner's Manual 5 Chapter 1 Introduction Overview The PJ Master is a software to manage and control targets (Projectors and PDP monitors) in a network centrally, and forms a tree structure with the targets and servers. The top server manages operating condition of the targets centrally and provides functions to control targets and update the software remotely. [. . . ] and click OK button. * The multiple IP addresses are listed on the pull-down menu button if the server provides multiple network cards. * If "127. 0. 0. 1" appear on the pull-down button, the server may not connect to the network correctly. Make sure that the network cable is connected to the server correctly and the IP address is assigned to the server, and then restart the PJ Master. PJ Master Owner's Manual 27 Chapter 3 Basic operation Customizing the display columns Changing the status column indication 1. On the window, check the column name you want to display on the status list view window . Column Target Name Power Status Lamp Status Input Signal Input Status Input Select Network Status Temperature A Temperature B Temperature C Lamp Time IP Address Model Name Projector Time PJ-Net Ver. PJ Ver. Description Name of the network equipment Status of the network equipment (ON:Normal, OFF:Normal, OFF:P-Mng, Cooling, CountDown, etc. ) Status of lamp (On, Off, Err, LampNonLight, etc. indicated with lamp1, lamp2, lamp3, lamp4 sequentially) Name of input signal (Analog, Digital, S-Video, Video, Y/Cr/Cb, Y/Pr/Pb, etc. ) Status of input signal (On, Off, Interrupted) Displays input mode (1, 2, 3 etc) Status of network connection (Disconnect, Connect) Displays inside temperature A of the equipment (in Celsius or Fahrenheit) Displays inside temperature B of the equipment (in Celsius or Fahrenheit) Displays inside temperature C of the equipment (in Celsius or Fahrenheit) Displays lamp use time (Indicated with lamp1, lamp2, lamp3, lamp4 sequentially) Displays IP address of the equipment Displays model name of the equipment Displays accumulated projector use time Displays the version of the PJ Master or Network Board firmware Displays the version of the projector firmware 3. To change order of the display column on the status list, select column you intend to change order and click To up or To down. The setting window will close. * When specifying the column width by numeric value, enter number (0 to 9999) onto "Column width" text box. * When changing the column width or column order on the status list view window, it is reflected to the column selection window. * Some of the column items may not effective depending on the connected target. 28 Warning setting Font setting Changing fonts on the status list 1. Click OK to close window. Warning value setting The threshold value of lamp use time and internal temperatures of the target are set up with this procedure. * The command data are stored in the defined files, Define_PJ. def for projector or Define_PDP. def for PDP monitor, in the folder PMS/Program. If you want to add the new command, enable you to edit these defined files. For further information, see "Customizing the command list" on chapter 4 (p. 46). Condition setting By using the condition function, when executing the command defined by the Global Setting, it is possible to set as its command is executed after checking the target status. For example: Set screen mode to "Wide" for model "PLC-XP50" only. At first, check if the model name of the targets is "PLC-XP50", and then check if the target is in the power-on mode, after that execute the command "Screen Wide". * Check the power status before executing the screen mode change command as it is not possible to change the screen mode if the projector is in the stand-by mode. * The maximum length of the command text including the condition text is 512 characters. PJ Master Owner's Manual 33 Chapter 3 Basic operation Condition setting example 1. Select a target on the status list view window or a server on the tree view window. Click or button on the tool bar or select Global Setting from Projector or PDP menu. The setting window will appear. - The commands which are not effective to the selection are disabled. 3. Enter command and status, and set retry on or off. Item Setting example Command: CR MODELNM Status: PLC-XP50 Retry: OFF -- only execute command once. [. . . ] If you select a top server or a server which has the targets, the targets under the selected server are targets to update the firmware. Also you can select multiple targets on the status list view window individually. Browse and select a prepared "****. bin" file on the desktop. Click Condition if you want to set condition command, or click OK if you want not to set the condition command. [. . . ]