User manual SANYO AVM-32F4

[. . . ] TABLE OF CONTENTS Introduction Safety Instructions Location of Controls Remote Control Use Antenna Connection Cable TV(CATV) Connection Video/Audio Connections Basic Operation Basic Menu Operation Set-Up Antenna Selection Auto Channel Programming Manual Memory (Channel Add/Delete) Fine Tuning LNA Effects 2 3 4 5 6 7 8 10 11 13 Picture Adjustment P. STD Button Custom(Manual) Adjustment 18 Sound Adjustment Using S. STD Button Using On-Screen Menu Equalizer Headphones Surround Sound MTS 20 Clock/Timer Other Functions Picture-in-Picture (PIP) AVM-32F9 ONLY V-Chip Operation Reception Disturbance Care and Maintenance Troubleshooting Guide Sanyo Comfort Warranty 28 31 34 36 48 48 49 50 1 INTRODUCTION Congratulations on your purchase of this Sanyo MTS stereo TruFlat TM screen television. Distortion-Free Images - Sanyo TruFlat TM recreates the theater screen experience by eliminating distortion that a curved conventional TV screen produces. Wider Viewing Angle - No curves mean that the full picture can be seen from a wider seating range in your room. Less Reflection - Window and other reflections are reduced because of the curve-free design. [. . . ] Move the cursor to SOUND by pressing the CH / buttons and press the VOL + button. MONO/SAP 2 SOUND SOUND EQUALIZER HEADPHONE BALANCE SURROUND MTS : SEL. + : SET : STANDARD Move the cursor to MTS by pressing the CH / buttons. :0 : OFF : STEREO : PREV. 3 Press the VOL + button. STEREO SAP MONO NOTES If the received signal is weak, noise may be heard. In such a case, press MTS button to set to the MONO mode for better sound reception. Even if both STEREO and SAP broadcasts are received, both broadcasts cannot be heard at the same time. Transmission of CABLE TV signals may differ from off-air TV broadcasts. SOUND SOUND EQUALIZER HEADPHONE BALANCE SURROUND MTS : SEL. + : SET : STANDARD SOUND SOUND EQUALIZER HEADPHONE BALANCE SURROUND MTS : SEL. + : SET : STANDARD :0 : OFF : STEREO : PREV. :0 : OFF : SAP : PREV. 26 27 CLOCK/TIMER CLOCK You can set the television's clock so that the current time will be displayed when you press the MENU button on the remote control. You must set the current time before you can set the automatic On/Off timer. CLOCK/TIMER ON/OFF TIMER The ON/OFF timer lets you use alarm and automatic off functions. 1 MENU PICTURE SOUND TIME SETUP FUNCTION LANGUAGE : ENGLISH : SEL. The " MENU " is displayed on the screen. MENU PICTURE SOUND TIME SETUP FUNCTION LANGUAGE : ENGLISH : SEL. + : ENTER : EXIT Press MENU button and move to " TIME " option by using CH / buttons. Press VOL + button and press it again. 2 Adjust "HOUR " with CH / buttons. Whenever these buttons are pressed, the hour indication increases or decreases by 1. MENU PICTURE SOUND TIME SETUP FUNCTION LANGUAGE : ENGLISH : SEL. + : ENTER : EXIT 2 TIME CLOCK TIMER ON TIME OFF TIME ON CHANNEL : MOVE WHITE RED : : : : : AM 12:00 OFF AM 12:00 AM 12:00 TV 2 : PREV. Move the cursor to TIME by pressing the CH / buttons and press the VOL + button. "TIME " menu is displayed on the screen. : ADJ 3 Press VOL + button and adjust "MINUTE " by using CH / buttons. Whenever these buttons are pressed, the minute indication increases or decreases by 1. NOTES Press the "MENU "button to return to the main menu. TIME CLOCK TIMER ON TIME OFF TIME ON CHANNEL : : : : : AM 06:00 GREEN ON AM 12:00 AM 12:00 TV 2 : PREV. 3 TIME CLOCK TIMER ON TIME OFF TIME ON CHANNEL : : : : : GREEN AM 06:00 OFF AM 12:00 AM 12:00 TV 2 : PREV. Move the cursor to TIMER by using CH / buttons and press VOL + button to set TIMER ON. + : ENTER 4 28 If you have not yet set the television's clock, the message "CLOCK STOPPED" is displayed. If this happens, refer to "CLOCK" on previous page. 29 CLOCK/TIMER CLOCK/TIMER ON TIME CHANNEL NUMBER 4 TIME CLOCK TIMER ON TIME OFF TIME ON CHANNEL : : : : : AM 06:00 ON AM 07:30 AM 12:00 TV 2 : PREV. Move the cursor to ON TIME by using CH / buttons and press the VOL + / buttons to set the time. (Refer to page 28) You can select the channel on which the TV turns on as programmed by ON-TIMER. This function will not work if the TIMER is set to OFF or the current time has not been set. TIME CLOCK TIMER ON TIME OFF TIME ON CHANNEL : : : : : AM 06:00 ON AM 07:30 PM 10:15 TV 2 : PREV. 1) Move cursor to ON CHANNEL and press CH / key. + : ENTER TIME CLOCK TIMER ON TIME OFF TIME ON CHANNEL : : : : : AM 12:00 ON AM 07:30 PM 10:15 TV 2 : PREV. Move the cursor to OFF TIME by using CH / buttons and press the VOL + / buttons to set the time. OTHER FUNCTIONS 1. [. . . ] Usually caused by interference from automobile ignition systems, neon lamps, electric drills and other electric appliances. GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or other objects. Changing the direction or position of the antenna may improve the reception. Poor picture or no picture Poor reception on some channels. SNOW: If you are located on the fringes of a television reception area, the signal will be weak, and your picture may contain many small dots. When the signal is extremely weak, it may be necessary to install an external antenna to improve the picture. Poor color or no color RADIO FREQUENCY INTERFERENCE: This interference produces moving ripples or diagonal streaks, and in some cases causes loss of contrast in the picture. Picture wobbles or drifts No CATV reception Horizontal or diagonal bars on screen No reception above Channel 13 No remote operation PICTURE SIZE VARIATION: A slight variation in picture size is normal when you adjust the CONTRAST or BRIGHTNESS controls. NOTE: If you subscribe to a cable service and any these symptoms appear, the problem may be caused by the cable company. CARE AND MAINTENANCE To prevent fire or shock hazard, disconnect your unit from the AC power source when cleaning. [. . . ]