User manual SANYO AVL-472

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION RISK OF ELECTRIC SHOCK CAUTION-To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www. eia. org FCC STATEMENT FCC Notice LCD TV: A CLASS B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] Connect the Audio cable between the AUDIO input jack on the unit and AUDIO output jacks on the receiver and/or DVD player. 1. Turn on your LCD TV , press INPUT button on the remote control to select Component 1 or 2. Turn on your DTV receiver and/or DVD player. To Watch 12 Connections (continued) Connect a VCR (for recording) or external amplifier R Y W Audio cable Video cable Audio cable Y W R Yellow (VIDEO) White (AUDIO L) Red (AUDIO R ) To Audio inputs R W Y W R ANT OUT VIDEO AV OUT L AUDIO R ANT IN VCR for recording VIDEO AV IN L AUDIO R External Amplifier Rear of the VCR Connect the Audio/Video cables between the Audio (L/R)/Video jacks on the unit and VCR. Connect the Audio cables between the Audio (L/R) jacks on the unit and external amplifier. Press the Record button to begin recording. How to connect: - or - To record program To enjoy high-quality sound through an external amplifier Note: The operations of the amplifier may be different depending on model. Please read the user manual of your amplifier to confirm proper operation. The AV output terminals output audio/video signal inputted from Antenna input or AV inputs. 13 Basic Operations Turning the Unit On and Off Turning On Insert the power cord into the wall outlet. Press the Power button on the remote control, the unit will be turned on and you will be ready to use its features. Turning Off With the power on, press the Power Note: You can also use the Power button on the remote control to turn off. button on the control panel on the main unit. Viewing the Menu and Displays This unit has a simple, easy-to-use menu system that appears on the screen. The unit also lets you display the status of many of your TV features. Menu navigation 1 2 3 4 5 With the power on, press the MENU button to display the main menu. Press OK or4button to confirm, enter sub-menu or toggle the settings of the selected menu item. However digital coverage via cable or satellite is widespread (digital cable or satellite receiver required). Channel Selection Using the Channel up/down buttons (CH+ or CH-) Press the CH+ or CH- to cycle among available channels found. Using the direct select buttons (0-9 and dash buttons) Press the number buttons (0-9) and the dash button (-) to go directly to a channel. For example, if you want to select channel 8-3, just key in `8', `-', `3' on the remote control. Note: =When you use the number buttons, you can directly select any channel within the channel range . =To select an analog channel, you may directly input its major channel number. It is unnecessary to input the =In some situations virtual channel numbers have no correspondence to physical frequencies. minor channel number of zero. Using the button Press this button to switch between the current channel and the last viewed channel. 17 Screen Setup for HDMI, S-Video, regular audio/video inputs and analog TV Customizing the Picture Picture Mode Contrast 50 Brightness 50 Color Sharpness Aspect Ratio Advanced Video Menu To Move OK To Select Exit To Exit 50 0 Wide User 1 2 3 4 5 Press MENU to display the menu main page. Press OK or4 to access the submenu. Video Audio Setup Feature Within the menu, use 5, 6, 3or4 to navigate or adjust. Press OK or 4button to confirm, enter sub-menu or toggle Notes: the settings of the selected menu item. The menu items may be different when the unit works in different mode. Option Function Choice/remarks Note: you may directly press PICTURE button on the remote control to select. User/Nature/Soft/Bright 4: stronger 3: weaker 4: lighter 3: darker 4: stronger 3: weaker Picture Mode Contrast Brightness Selects a desired picture mode. Adjusts screen brightness for easier viewing of dark picture such as night scenes and black hair. Selects screen aspect ratio. Color Sharpness Aspect Ratio 4: sharper 3: softer Note: you may directly press ZOOM button on the remote control to select. 'Wide" & "Cinema" stretch the image in the width to fill the screen of a 4:3 program. "Cinema" minimizes the effect in the centre, increases at the edges. [. . . ] This product is not designed to display fixed image patterns for extended periods of time. Important Information Regarding Use of Video Games, Computers, Captions or Other Fixed Image Displays. The extended use of fixed image program material can cause a permanent "shadow image" on the LCD panel. Turn the power off when not in actual use. This background image is viewable on normal programs in the form of a stationary fixed image. This type of irreversible LCD panel deterioration can be limited by observing the following steps: Cleaning and Maintenance If the surfaces are extremely dirty, use a soft cloth dipped in a soap and water solution or a weak detergent solution. [. . . ]