User manual SANYO AVL-193

[. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC CAUTION: Pursuant to 47CFR, Part 15. 21 of the FCC rules, any changes or modifications to this monitor not expressly approved by the manufacturer could cause harmful interference and would void the user's authority to operate this device. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures to counter interference. 1 Important Safety Precautions Electrical energy can perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. [. . . ] Welcome! Select Language Press / to select the desired language listed on the screen, and then press OK to confirm and continue. Use the Up and Down arrows on your Remote Control and Select the language you want to use for menus and message screens. English Français Español Select Time Zone Press / to select a proper time zone according to your area, and then press OK to confirm and continue. If you want to return to previous screen, please highlight [GO BACK] item and press OK to return. Press OK to continue in English Time Zone Use the Up and Down arrows and press Select on your Time Zone. Alaska (US) Hawaii Pacific (US, CAN) Mountain (US, CAN) Central (US, CAN) Setting Daylight Saving Press / to highlight [Yes] item if you want to observe daylight saving, or [No] to abandon daylight saving and then press OK to confirm and continue. If you want to return to previous screen, please highlight [GO BACK] item and press OK to return. GO BACK Press OK to continue Eastern (US, CAN) Daylight Saving Do you observe Daylight Saving? Yes No Selecting RF Input Source Press / to select [Antenna] or [Cable] according to what kind of connection is made to your TV, and then press OK to confirm and continue. If you choose [Cable], there are 3 kinds of CATV system, including STD, HRC and IRC. If you want to return to previous screen, please highlight [GO BACK] item and press OK to return. GO BACK Press OK to continue RF Input Source Select the source for your television signal. Antenna Cable GO BACK Press OK to continue Start Auto Program. . . Once you have finished selecting RF input source, the unit starts auto program. A progress bar is displayed while available analogue and ATSC digital channels are being scanned. If you select [Stop Scan] to cancel the Auto Program before all receivable channels are scanned, you need to run Auto Program again at a later time. Auto Program will create a list of receivable channels for the current input . You will be required to run Auto Program for RF input to create a list of available channels. 23 Scanning Channels Signal 2. 0 Channels Found Digital: 3 Analog:3 2. 1 2. 2 3. 0 4. 0 4. 1 Stop Scan Scanning may take a few minutes - Please be patient (Example) Getting Started Setting a Secret Number (Password) For additional protection to your TV and to your user's settings from being accidentally changed, you may want to set a secret number first as below. 1. Highlight [Locks]. . . . . . . . . . . Use or button. Picture Audio Settings Channels Locks Guide Enter New PIN: Confirm New PIN: 3. Press it again to cancel the mute. Using FREEZE button Press FREEZE to temporarily capture a program's picture. You can use this feature to write down information such as phone numbers, recipes, etc. You may press any key to cancel FREEZE and return to normal viewing. FREEZE The TV automatically cancel FREEZE and return to normal viewing in about a minute. Using ZOOM button Press ZOOM repeatedly to choose a desired non-high definition screen aspect ratio. Normal ZOOM The zoom mode options may Select to match the source's image. ( 4:3 to 4:3, 16:9 to 16:9) differ from different formats of the input signal. Normal Example: Source Final When you choose NORMAL to view a 4:3 program, two black bars remain on the two sides of the screen. To protect the screen, when you are viewing a 4:3 program, please DO NOT use the NORMAL feature for a long period of time. 26 Watching TV Using ZOOM button Direct Select to detect the resolution of the signal and display an image with the same number of pixels on the screen. Direct Example: Source Final Full Screen Select to enlarge the 4:3 picture horizontally only, to fill the display area. Full Screen Example: Source Panoramic Final (some shape distortion) Select to enlarge the 4:3 picture to fill the 16:9 screen, keeping the original image as much as possible. Panoramic Example: Source ZOOM 1 Final (some shape distortion) Select to enlarge the picture horizontally and vertically to an equal aspect ratio that fills the wide screen. ZOOM 1 Example: Source ZOOM 2 Final (No distortion, a bit of top/bottom picture loss) Select to view wide-screen DVDs in full screen. [. . . ] Now when you press VOL+, VOL-, or Mute, the selected device (for example, TV) will control the volume regardless of the current mode. Unlocking All Volume Control (Restoring Global Unlock) 1. Volume is now independently controlled for all programmed devices. Unlocking a Single Device's Volume Control 1. Volume is now independently controlled for the selected devices. Troubleshooting Problem Solution LED does not blink when you Replace new batteries. LED blinks when you press a Make sure the remote is aimed at your device and is key, but device does not not more than 15 feet away. [. . . ]