User manual SANUS VISIONMOUNT TILT AMP SWIVEL CEILING MOUNT-LC1A

[. . . ] Typical wall anchors do not have sufficient holding power to support this mount. It is up to the installer to verify the safety of any installation method or hardware that is not provided by or recommended by Sanus Systems. Sanus Systems makes every effort to assure all necessary television mounting hardware is included. If the television mounting hardware you need is not included please consult your local hardware store or call Sanus Systems. [. . . ] If the television mounting hardware you need is not included please consult your local hardware store or call Sanus Systems. Required Tools: Drill, 3/16" drill bit, wrench set, Philips screwdriver Supplied Parts and Hardware: (Some parts are not shown at the same scale) Wall Plate - A Qty . 1 Arm Assembly - B Qty . 1 M4 x 12 mm Bolt - C Qty . 4 M5 x 12 mm Bolt - D Qty . 4 M6 x 12 mm Bolt - E Qty . 4 M4 x 30 mm Bolt - F Qty . 4 M5 x 30 mm Bolt - G Qty . 4 M6 x 35 mm Bolt - H Qty . 4 M4 Lock Washer - I Qty . 4 M5 Lock Washer - J Qty . 4 M6 Lock Washer - K Qty . 4 Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 10. 11. 06 (6901-100044) Customer Service: 800. 359. 5520. See complementary Sanus products at www. sanus. com M4/M5 Spacer - L Qty. 1 Step 1: Mount the Wall Plate: Wood Stud installation only CAUTION: Do not overtighten the Lag Bolts (P). Tighten Lag Bolts until the Lag bolt Washer (Q) is pulled firmly against the Wall plate (A). If there is a layer of drywall or other material, this drywall or other material may not exceed 5/8 inch [15. 8 mm] in thickness. Failure to heed this caution may result in property damage and/or personal injury. Wood Stud Mounting: The Wall Plate (A) must be mounted to a wood stud. It is a good idea to verify where the stud is located with an awl or thin nail. Pre-drill a 2. 5" [63. 5 mm] deep hole at the desired height in the stud using a 3/16" drill bit. Diagram 4 Wall Transfer Bracket B A Step 5: Add Safety Bolts CAUTION: make sure the Safety Bolt (S) is tight. A loose Safety bolt will result in an unstable installation which may result in property damage and/or personal injury. Thread a Safety bolt (S) into the threaded hole on each side of the Transfer Bracket and tighten them with a phillips screwdriver until they are tight. See the detailed View of Diagram 5 for assistance. Diagram 5 Detailed View Transfer Bracket S NOTE: Lower Hole on transfer bracket may be used to add a padlock for added security. Step 6: Leveling and Adjusting Tension on the Monitor CAUTION: Do not remove the Tension Nuts labeled in Diagram 6a. Once the television is mounted onto the Wall Plate (A), and the Safety Bolts (S) are tight, it can be adjusted to level. Slightly loosen the two Allen Bolts on the back of the Arm Assembly (B). Once those two bolts are loosened, the television can be adjusted ±6º until level. If you need to adjust the tension of the tilt, you can do so with the Tension Knobs. The Tension Nuts labeled in Diagram 6a can be slightly loosened or tightened to adjust the tension of the Arm Assembly. If you need to adjust the Tension Nut closest to the TV, you must remove the Safety Bracket, adjust the tension and re-install the Safety Bracket as shown in the Safety Bracket installation view of Diagram 6b. [. . . ] The Tension Nuts labeled in Diagram 6a can be slightly loosened or tightened to adjust the tension of the Arm Assembly. If you need to adjust the Tension Nut closest to the TV, you must remove the Safety Bracket, adjust the tension and re-install the Safety Bracket as shown in the Safety Bracket installation view of Diagram 6b. Diagram 6a Safety Bracket Tension Nut B Diagram 6b Safety Bracket Allen Bolts Tension Knobs Tension Nut Step 7: Cable/Wire Management CAUTION: Do not run cables through a pinch point. Running cables through pinch points may result in damage to the cables and/or personal injury. [. . . ]