User manual SANUS VISIONMOUNT LCD WALL MOUNT-VM300

[. . . ] If you determined that your TV requires a Bolt with a M6 Diameter, thread a M6 x 35 (r) Bolt through a Lock Washer (i), the Monitor Bracket, a M6 Spacer (l) and into the TV, as shown on the right side the Detailed View of Diagram 4 for assistance. Detailed View Assembly Instructions for Model VM300 Thank you for choosing a Sanus Systems Vision Mount wall mount. The VM300 is designed to mount up to 40" LCD flat panel televisions weighing up to 80 lb to a vertical wall. [. . . ] Diagram 5a Diagram 5b TV (1) Wall Plate - a* (1) Locking Monitor Bracket - b* (1) Monitor Bracket - c* (3) Lag Bolts - d (3) Lag Bolt Washer - e (3) Concrete Anchor - f (4) M4 Lock Washer - g (4) M5 Lock Washer - h (4) M6 Lock Washer - i a wall (4) M4/M5 Washer - j tab (4) M4 x 10mm Monitor Bolt - m extension handle (4) M4 x 30mm Monitor Bolt - p (4) M5 x 30mm Monitor Bolt - q (4) M6 x 35mm Monitor Bolt - r (4) M5 x 12mm Monitor Bolt - n (4) M6 x 12mm Monitor Bolt - o (4) M4/M5 Spacer - k (4) M6 Spacer - l Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 10. 04. 04 Customer Service: 800. 359. 5520. See complementary Sanus products at www. sanus. com Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 10. 04. 04 Customer Service: 800. 359. 5520. See complementary Sanus products at www. sanus. com Step 1: Mount the Wall Plate: Wood Stud, Brick, Solid Concrete, and Concrete Block mounting options are provided. Wood Stud Mounting: The Wall Plate (a) must be mounted to a wood stud. Pre-drill a 2. 5" deep hole at the desired height in the stud using a 3/16" drill bit. Use the Wall Plate as a template to mark the location of the second hole. Make sure the Wall Plate is level and drill 2. 5" a deep hole using the 3/16" drill bit in the marked location. Attach the Wall Plate to the wall using two Lag Bolts (d) and two Lag Bolt Washers (e). Make sure the Wall Plate is oriented so the flat surface in the center of the plate is against the wall as shown in Diagram 1a. Tighten Lag Bolts only until the Lag Bolt Washer is pulled firmly against the Wall Plate. Diagram 1a d e Step 2: Select the Appropriate Hardware for your television Always make sure the television is unplugged before threading any bolt into the back panel!Thread bolts carefully into your television by hand before tightening. If you are unable to find appropriate hardware for your television, consult a local hardware store or call Sanus Systems. Locate the threaded inserts on the back of your flat panel television and determine which of the provided Bolts is the correct diameter. To test each diameter, thread the Bolts carefully into your television by hand until you find the diameter that correctly fits. Televisions with a flat back will require one of the shorter Bolts and no spacer. [. . . ] Attach the Wall Plate to the wall using 3 Lag Bolts (d) and 3 Lag Bolt Washers (e). Tighten Lag Bolts only until the Lag Bolt Washer is pulled firmly against the Wall Plate. Diagram 1b d e Step 3: Attach Monitor Brackets to a television with a flat back Make sure the Locking Monitor Bracket (b) is located on the left side as shown in Diagram 3. [. . . ]