User manual SANUS VISIONMOUNT LCD WALL MOUNT-VM200

[. . . ] Step 3: Mounting the Wall Plate - wood stud, brick, solid concrete and concrete block mounting options are provided Wood Stud Installation: The Wall Plate (a) must be installed into a single wood stud. Use the Wall Plate as a template mark a location on the wall, one in the top row of slots and the other in the corresponding slot in the bottom row. Pre drill a 2. 5" deep hole into the wood stud by using a 3/16" drill bit. [. . . ] Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800. 359. 5520 or www. sanus. com. Check carefully to make sure that there are no missing or defective parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement parts for products purchased through authorized dealers will be shipped directly to you. Do not use this product for any purpose that is not explicitly specified by Sanus Systems. Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus Systems before returning products to the point of purchase. Note: The supplied wall mounting hardware is not for metal stud or old cinder block walls. If you are uncertain about the nature of your wall, consult an installation contractor. Sanus makes every effort to assure all necessary television mounting hardware is included. If the hardware you need is not included please consult your local hardware store or call Sanus Systems. Required Tools: Drill, 3/16" drill bit, (1/2" masonry bit for brick, concrete, or concrete block installations), socket set and a Phillips screw driver f Supplied Parts and Hardware: Some parts not shown as actual size* d e a d e a (1) Left Monitor Bracket - b* (1) Wall Plate - a* (1) Right Monitor Bracket - c* Step 4: Attach Monitor to Wall Plate Rotate the latch handle into its most open position and hang the hooks of the Left and Right Monitor Brackets (b, c) over the tab on the top of the Wall Plate (a) as shown in Diagram 4a. Once the Monitor Brackets are attached to the Wall Plate, rotate the latch handles on each Monitor Bracket until they click into place. The tip of the latch handle should now be tucked up behind the tab on the bottom of the Wall Plate as shown in the Detailed View of Diagram 4b. You may place a pad lock through the hole in the bottom of the latch handle if you wish to add security to the installation. Diagram 4a Diagram 4b Detailed View (3) Lag Bolt - d (3) Lag Bolt Washer - e TV Mounting Hardware: (3) Concrete Anchor - f (4) M4 x 10 mm Bolt - g b, c bottom tab tip of latch handle (4) M4 x 30 mm Bolt - j (4) M5 x 12 mm Bolt - h (4) M6 x 12 mm Bolt - i (4) M5 x 30 mm Bolt - k (4) M6 x 35 mm Bolt - l (4) M4 Lock Washer - m (4) M5 Lock Washer - n (4) M6 Lock Washer - o latch handle hole for padlock (4) M4/M5 Washer - p (4) M6 Washer - q (4) M4/M5 Spacer - r (4) M6 Spacer - s Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 8. 17. 05 Customer Service: 800. 359. 5520. [. . . ] You will thread the Bolt through the appropriate Lock Washer (m, n, o), the corresponding Washer (p, q), the Monitor Bracket (b, c), a Spacer (r, s), and finally into the TV. Make sure the Monitor Brackets are vertically centered and level with each other. M4 Diameter Bolt M6 Diameter Bolt c c g m p q o b j i r p m s b l o q M5 Diameter Bolt Diagram 1 M5 Diameter Bolt Diagram 2 c c h r n n p p k [. . . ]