User manual SANUS VISIONMOUNT LCD WALL MOUNT-LT25

[. . . ] Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800. 359. 5520 or www. sanus. com. Check carefully to make sure that there are no missing or defective parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. [. . . ] Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement parts for products purchased through authorized dealers will be shipped directly to you. Do not use this product for any purpose that is not explicitly specified by Sanus Systems. Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus Systems before returning products to the point of purchase. Required Tools: Drill, 1/4" Drill Bit, wrench or socket set, phillips screw driver Check carefully to ensure that no hardware or parts are missing Note: Hardware shown at actual size *Some items not shown at same scale (6) Button Head Bolt - a (6) 1/4 20 Nut - b (6) Washer - c (4) M8 Nut - d (4) M8 x 16 Bolt - e (4) M8 Lock Washer - f (4) Furniture Bolt - g (4) Wood Screw - h (1) Allen Key - i (1) Base - j (1) Left Glide - k (1) Right Glide - l (1) Top Assembly - m * (1) Handle - n (1) Front Cover - o Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 4. 05. 05 Customer Service: 800. 359. 5520. See complementary Sanus products at www. sanus. com TV Attachment Hardware: (4) M4 x 10 Bolt - p (4) M4 x 30 Bolt - q (4) M6 x 12 Bolt - r (4) M6 x 35 Bolt - s (4) M4 Lock Washer - t (4) M6 Lock Washer - u (4) M4 Spacer - v (4) M6 Spacer - w Step 1: Prepare Holes in Mounting Surface Section A: Mounting the VMPO to the Sanus CFAR47cb On the bottom side of the Mid Shelf on the CFAR47cb you should see 6 starter holes that have been pre-drilled in a pattern that is shown in Diagram 1. With a Drill and a 1/4" Drill Bit, proceed to drill out all 6 holes so they go all the way through the shelf. Diagram 5 Detailed View U shaped slit n o h j Step 6: Adjust the height of the Top Assembly Using the Allen Key (i), loosen the pin that is shown in the Detailed View of Diagram 6. Once the Pin and the Nut are removed, raise or lower the free moving part of the Top Assembly (m) to the desired height and reinsert the Pin and the Nut into the appropriate hole. Tighten with the Allen Key. Diagram 6 Detailed View pin nut m Step 7: Attach Flat Panel LCD directly to VMPO To figure out the hardware needed to attach the VMPO directly to the TV, start by determining the diameter of the Bolt (M4 or M6) your TV requires by hand threading them into the threaded insert on the back of the TV. Once you have determined the correct diameter, see the appropriate Diagram below. You will thread the Bolt through the appropriate Lock Washer (t, u), the Top Assembly (m), and finally thread it into the TV. Proceed to tighten all 4 Bolts until tight with a phillips screw driver. Note: Instances where there is an obstruction near the threaded insert in the back of the TV will require the use of a Spacer (v, w) and the longer Bolt (q, s). M4 x 10 Diagram m t p v m t q M4 x 30 Diagram M6 x 12 Diagram m u r M6 x 35 Diagram u s w m If using a VM200 for tilt compatibility with flat panel LCD sets follow Step 8. [. . . ] Note: Instances where there is an obstruction near the threaded insert in the back of the TV will require the use of a Spacer (v, w) and the longer Bolt (q, s). M4 x 10 Diagram m t p v m t q M4 x 30 Diagram M6 x 12 Diagram m u r M6 x 35 Diagram u s w m If using a VM200 for tilt compatibility with flat panel LCD sets follow Step 8. Step 8: Attach the VM200 Wall Plate to Top Assembly Insert a M8 Bolt (e) through the appropriate hole in the VM200 Wall Plate, the Top Assembly (m), the M8 Lock Washer (f), and thread into a M8 Nut (d). [. . . ]